GOWIN GW2AR-18 Programming And Configuration Manual Download Page 16

Page: 16 / 97

3 Configuration Modes

3.2 Arora Family of FPGA Products

UG290-2.3E

7(87)

Table 3-2 Configuration Modes

Configuration Modes

MODE[2:0]

Description

JTAG

XXX

External Host configures Arora Family of
FPGA products via JTAG interface.

GowinCONFIG

MSPI

000

As Master, FPGA reads data from
external Flash (or other devices) via the
SPI interface

SSPI

001

External Host configures Arora Family of
FPGA products via SPI interface.

SERIAL

101

External Host configures Arora Family of
FPGA products via DIN interface.

CPU

111

External Host configures Arora Family of
FPGA products via DBUS interface.

Note!



[1] The unbound mode pins are grounded by default;



[2] The JTAG configuration mode is independent of MODE value;



[3] The SPI interfaces of the SSPI and MSPI modes are independent of each other;



[4] The CPU configuration mode and SERIAL configuration mode share SCLK,
WE_N and CLKHOLD_N. The data bus pins for the CPU configuration mode share
pins with MSPI and SSPI configuration modes.

Note!

For details about configuration pins, pin reuse, and pin functions and application, please
refer to 4 Configuration Pin.

Summary of Contents for GW2AR-18


































































































Search results

Summary of Contents for GW2AR-18

Reviews:

Related manuals for GW2AR-18

Brands by name

Popular brands

GOWIN GW2AR-18, Programming And Configuration Manual

Search results

Summary of Contents for GW2AR-18

Reviews:

Related manuals for GW2AR-18

Brands by name

Popular brands