manualshive.com logo in svg

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Share
Download
Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 108

228

122

353

355

184

370H

Figure 76: Cartridge-type mechanical seal and seal-chamber cover

4.

Install the seal-chamber cover (184).

a) Set up a sling to the eyebolt and to the overhead lifting device.

b) Lift the seal-chamber cover (184) and position it so that it aligns with the shaft.

c)

Install the seal-chamber cover (184) on the power end by guiding the cover carefully over the
cartridge-seal rotary.

Ensure that the gland studs smoothly enter the holes in the cartridge-seal gland and that the cover
(184) fits into the bearing frame lock.

d) Install the seal-chamber cover (184) and bearing-frame bolts (370H) and tighten them using an

alternating pattern.

Torque the bolts to the values shown in the Maximum torque values for 3700i fasteners table.

e) Install the gland stud nuts (355) and tighten evenly to the torque values shown in the Maximum

torque values for 3700i fasteners table.

5.

Tighten the setscrews in the locking collar.

6.

Disengage the spacer ring or clips.

7.

Verify that the shaft (122) turns freely.
If you detect rubbing or excessive drag, then determine the cause and correct it.

6.6.5 Install the impeller

 

CAUTION:

Risk of physical injury from sharp edges. Wear heavy work gloves when handling impellers.

 

It is recommended that you repeat the runout checks on the seal-chamber cover face, lock, and wear-
ring surfaces as described in 

6.6.3 Install the seal-chamber cover on page 101

.

1.

Install the impeller key in the keyway of the shaft.
The key should be at the top (12 o’clock) position for the impeller installation.

2.

Install the impeller on the shaft.
Apply anti-galling compound to the impeller bore to aid in assembly and disassembly.

3.

Install the impeller nut and tighten to the torque values shown in the Maximum torque values for
3700i fasteners table.

6.6 Reassembly

106

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands