Gotting HG G-73650-A Basics, Commissioning And Software Download Page 50

Page: 50 / 76

Commissioning

English, Revision 07, Date: 07.03.2018

4.11 (G) Parameters Navigation

Using this menu the parameters for the sensor fusion and for the steering controller
can be set Following selection screen appears:

Figure 21

Screenshot: Parameters Navigation

Sprung_Status

Indicates, why the calculated position was not trans-
ferred into odometry
-

0x01: Abs_Fehler_W > Abw_Tab_Winkel_Wert

0x02: Abs_Fehler_Quer > Abw_Tab_Quer_Wert

0x04: Abs_Fehler_Laengs >
Abw_Tab:Laengs_Wert

0x08: fabs(t_dy_1) > 0.25 m

OdodSumme_Weg

Distance since last used transponder

Genauigkeit

Estimated position accuracy

Guete_Messung

Estimated quality of measurement

Guete_Position

Estimated quality of position in odometry

Guete_Position_Weg

Estimated quality of position in odometry influenced
by the distance covered

Gewichtung

Intensity of influence of the calculated position of
odometry.

Position_OK

Set to 1, if position was initialized

Column

Name

Description

Table 31

Errorlogger: Vehicle Status (part 7 of 7)

Parameter Menu Navigation Controller

A: Main

B: Geometric

C: Accuracy

D: Steering

E: Steering Controller

F: Speed Controller

G: Sensorfusion

H: Vehicle Specials

I: Datalogging

[ESC] -> back/cancel

Summary of Contents for HG G-73650-A













































































Search results

Summary of Contents for HG G-73650-A

Reviews:

Brands by name

Popular brands

Gotting HG G-73650-A, Basics, Commissioning And Software

Search results

Summary of Contents for HG G-73650-A

Reviews:

Brands by name

Popular brands