Gotting HG 73840ZB Device Description Download Page 65 | Manualshive

Page: 65 / 65

background image

Copyright and Terms of Liability

English, Revision 06, Date: 12.07.2011

65

14 Copyright and Terms of Liability

14.1 Copyright

This manual is protected by copyright. All rights reserved. Violations are subject to pe-
nal legislation of the Copyright.

14.2 Exclusion of Liability

Any information given is to be understood as system description only, but is not to be
taken as guaranteed features. Any values are reference values. The product charac-
teristics are only valid if the systems are used according to the description.

This instruction manual has been drawn up to the best of our knowledge. Installation,
setup and operation of the device will be on the customer’s own risk. Liability for con-
sequential defects is excluded. We reserve the right for changes encouraging techni-
cal improvements. We also reserve the right to change the contents of this manual
without having to give notice to any third party.

14.3 Trade Marks and Company Names

Unless stated otherwise, the herein mentioned logos and product names are legally
protected trade marks of Götting KG. All third party product or company names may
be trade marks or registered trade marks of the corresponding companies.

«
...
63
64
65

Summary of Contents for HG 73840ZB


































































Reviews:

No comments

Related manuals for HG 73840ZB

RoadMate 360 - Automotive GPS Receiver

Brand: Magellan Pages: 96

Brand: u-blox Pages: 54

Brand: TELETRAC NAVMAN Pages: 35

EZY250LM MY400LMT/MY450LMT

Brand: Navman Pages: 110

Interphone GPS Bike

Brand: Cellularline Pages: 2

Brand: Queclink Pages: 16

Brand: Navibe Pages: 20

Brand: Garmin Pages: 236

GSM/GPRS/GPS OUTLINK 950

Brand: GPS-TEKNIK Pages: 15

Brand: GPS Vision Pages: 33

BI-868 TREK HW2

Brand: BITREK Pages: 32

Brand: Naxa Pages: 17

Brand: Raymarine Pages: 58

Brand: Teltonika Pages: 31

Brand: Black Box Pages: 36

Brand: Ercogener Pages: 71

Brand: FALK Pages: 2

Brand: Groupe Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands