manualshive.com logo in svg

Gotting HG 73840ZB, Device Description, Page: 28 / 65

Share
Download
Gotting HG 73840ZB Device Description Download Page 28

Software / Parameter Settings

HG 73840ZB

English, Revision 06, Date: 12.07.2011

28

4.5

C(A)N-Menu

Figure 14

Screenshot: CAN Menu

In addition to the above described status line, the CAN bus status is displayed: Bus 
online switches to Bus offline in case e. g. the CAN bus connector is removed or the 
CAN bus controller switches to 

BUSOFF

 status due to missing terminal resistor. Next to 

this message, the CAN open Node Status: stopped, preoperational or operational is 
displayed.

Within this menu it is possible to

-

switch the CANopen® output on/off with 

, similarly the serial interface will be 

switched on/off.

-

select the Node address within the range of 1 through 127 via 

,

-

select the listed Baud rates via 

, the function Autobaud is not implemented,

-

select the TPDO_1 operational mode via 

. With the values 1 through 240 it is 

possible to choose between synchronous, cyclic and, with 255, asynchronous 
operational mode. The following two menu functions only exist for the asynchro-
nous operational mode:

-

input the Inhibit time of the 

TPDO_1

 via 

. In 

TPDO_1

 the system status 

and the calculated distances are transmitted. The Inhibit time is the short-
est possible time period between two subsequential transmissions,

-

select the cycle time of the 

TPDO_1

 transmission via 

. In case both val-

ues are 0, 

TPDO_1

 is not transmitted.

-

change the so-called Heartbeat time via 

. A control message is transmitted with 

this cycle time. If the Heartbeat time is 0, this function is suppressed. If a value is 
set for the Heartbeat time, the Toggle-Bit of the knot status is no longer changed 
by remote telegrams (Node Guarding Function).

-

activate / deactivate the Autostart function via 

:

Peak 27935 @ 265   X/mm:     4   S: 4000 Code: 255  SCmin:   0 %

Bus offline                        Last Err: 8801  TxBuf: 10

         (T) CAN active                                     1

         (N)ode ID                            [1..127]:     1

         CAN-(B)audrate[20,50,100,125,250,500,1000 kB]:   125

         (C) TPDO_1 mode                  [1..240,255]:   255

         (D) TPDO_1 inhibit time      [0,20..10000 ms]:     0

         (E) TPDO_1 event time        [0,20..10000 ms]:    20

         (I) Heartbeat time          [0,100..65535 ms]:     0

         (A)utostart                                        1

         (H)i Byte first                                    0

         (Q)uit

Summary of Contents for HG 73840ZB


































































Reviews:

No comments