Gotting HG 73840ZB Device Description Download Page 26

Page: 26 / 65

Software / Parameter Settings

HG 73840ZB

English, Revision 06, Date: 12.07.2011

4.4

(O)utput-Input Settings

This menu offers the option of switching between OUT_1 to OUT_4. According to the
selection of menu point (



) these outputs will be used as indicators for the edgewise

deviation or as the code output for the low-ordered 4 bits of the bar code.

In the following figure the outputs OUT_1...OUT_4 were selected for the code output:

Figure 12

Screenshot: Menu (O)utput-Input Settings - output of threshold

The menu points (



) and (



) have here the following meanings:

By using



the time lag of the code output from OUT_1..OUT_4 to DATA_READY

pulse to OUT_5 can be chosen.

With



the duration of the DATA_READY pulse to OUT_5 can be set.

In the following figure the outputs OUT_1...OUT_4 will be used as indicators for edge-
wise deviation:

Peak 27889 @ 265 X/mm: 4 S: 4000 Code: 255 SCmin: 0 %

Parallel Output:

(X)-Deviation on OUT_1..OUT4

(1)CODE_OK (OUT_5) setup time [1..100 ms]: 20

(2)CODE_OK (OUT_5) duration [1..1000 ms]: 100

Parallel Input:

(P)arallel input active 1

(D)ebounce time [0..100ms]: 50

Analog Output:

(A)mplitude [-10..10V]: 10.00

(O)ffset [-5V..0..5V]: 0.00

(H)old analog value on loss of track 0

(B)ridge a track gap (n*20 ms) [0..25]: 20

Bridge a track (J)ump (n*20 ms) [0..25]: 0

Jump (I)ncrement [1..100 %]: 100

(Q)uit

Summary of Contents for HG 73840ZB


































































Search results

Summary of Contents for HG 73840ZB

Reviews:

Related manuals for HG 73840ZB

Brands by name

Popular brands

Gotting HG 73840ZB, Device Description

Search results

Summary of Contents for HG 73840ZB

Reviews:

Related manuals for HG 73840ZB

Brands by name

Popular brands