23
The Preset Select Screen
This is the first screen you will see, right after LD3’s start-up screen, unless you left your LD3 in
Song mode, the last time it was turned off. Here you can change preset, jump to LD3’s edit and
settings pages, and adjust the touch keyboard settings, as described on the previous pages.
On the top of this screen, the Sequencer bar/beat, that is currently being played back, is shown.
To the right of the bar/beat indicator, you will find a sequencer record indicator (REC) and a
sequencer tempo indicator. When the REC indicator is red, the sequencer are in record mode.
Touching the REC indicator, will switch the sequencer in and out of recording mode.
Touching the tempo indicator, will make LD3 jump to the sequencer main page, where you can set
the tempo. The tempo indicator will read “EXT”, if LD3 is set to external MIDI sync.
Below the bar/beat indicator, it says “Preset”, if LD3 is currently in preset mode, or “Song” if it is
currently in song mode.
Below this, the number and name of the currently selected preset/song is shown.
Below the preset name/number, you will find the touch screen keyboard.
Right above the preset name, 8 small VU-meters are shown. These shows the activity of voice 1 to
8.
Touch the “EDIT” field in the upper right corner of the screen, to enter the edit and setup pages.
Summary of Contents for Little deFormer 3
