GOSUNCN WeLink ME3616 Hardware Development Manual Download Page 53

Page: 53 / 55

Hardware Development Guide

ME3616

Figure 7–2 Material Module Pallet

NOTE:

Figure7-2 is just for refer

ence, it doesn’t represent the actual Material Module Tape Reel.

Otherwise, customers need make a loading tool similar to the tape reel. Customers can take out the module from the

packaging box, put them into the tape according to the sequence and direction, and then start SMT.

）

Tape Reel Dimension (unit: mm):

The following picture is the tape reel specific dimension for your reference:

A: Whole dimension:

B: Detailed dimension:

Figure 7–3 Tape Reel Dimension

）

Mounting Pressure:

In order to ensure a good contact between the module and the solder paste on main board, the pressure of placing the module

board on main board should be 2-5N according to our experiences. Different modules have different numbers of pads, therefore the

pressure selected are different. Customers can select proper pressure based on their own situations to suppress the module paste as

little as possible, in order to avoid the surface tension of the solder paste melts too much to drag the module during reflow.

Summary of Contents for WeLink ME3616
















































Search results

Summary of Contents for WeLink ME3616

Reviews:

Related manuals for WeLink ME3616

Brands by name

Popular brands

GOSUNCN WeLink ME3616, Hardware Development Manual

Search results

Summary of Contents for WeLink ME3616

Reviews:

Related manuals for WeLink ME3616

Brands by name

Popular brands