Gossen MetraWatt SSP 120 Series, Operating Instructions Manual

Page: 41 / 92

GMC-I Messtechnik GmbH 41
Display of Data Stored to Sequence Memory (11 ... 255) Upon
Execution of <RCL>
After executing the <RCL> command, selecting a memory
location (<

> or <

> key) and pressing the <ENTER> key, the
device is switched to the read-out mode. Values saved to
sequence memory blink at the display. The settings stored to the
selected memory location can now be browsed by pressing the
<
SELECT > key:
Uset Iset Voltage and current setpoints
tSEt Programmed dwell time
SSEt Signal output status
4.8.4 Setting Resolution with the <SELECT> Key
The numeric parameter can be set to varying degrees of
accuracy. Set the cursor to the desired decimal place within the
display to this end. The corresponding decimal place blinks in
order to indicate the current cursor position.
Resolution can be set for the following parameters:
Uset, Iset, Ulim, Ilim, OVset, Delay, tset and tdef.
Settings
☞
Select the desired parameter.
!
The parameter value blinks at the last selected decimal place.
☞
Press the < SELECT > key. The cursor (blinking decimal place) is
moved one place to the right.
☞
Repeatedly press the < SELECT > key until the cursor is
positioned at the desired decimal place.
☞
Set the parameter to the desired value with the <

> key or the
<

> key using the selected resolution.
Figure 4.8.4 Setting Resolution with the SELECT Key
4.9 Storing Data with the <SAVE> Key
The < SAVE > key is located at the left-hand side of the front panel
in the second row of keys underneath the < FUNCTION > key.
It makes the following functions available:
• Saving basic device settings
• Saving data to a Memory Location
• Deleting all data within a defined memory range from address
11 to 255
• Inserting additional data to a sequence
• Deleting an individual sequence memory
4.9.1 Saving Basic Device Settings
• Basic device settings can be saved to memory locations 1
through 10.
• These settings are saved to battery-backed memory.
Settings for all of the following parameters can be saved to
this memory:
USET/ISET OVSET TSET
OCP TDEF SSET
DELAY START OUTPUT
MINMAX STOP ULIM
REPETITION ILIM
Settings
☞
Select values for the desired parameters.
☞
Press the < SAVE > key.
!
Sto appears at the left-hand display, and the last selected
memory location number appears at the right-hand display.
☞
Select the desired memory location (1 to 10) with the <

> or
the <

> key.
☞
Acknowledge by pressing the < ENTER > key.
☞
Exit the SAVE function by pressing the < CE/LOCAL > key.
☞
Switch to the respective function by pressing the < FUNCTION >
key, the < SELECT > key or the < RCL > key, or by slightly turning
the current or voltage adjusting knob.
Figure 4.9.1 Saving Device Settings
4.9.2 Saving Data to a Memory Location
Functions
• Sequence data can be saved to memory locations 11 through
255.
• These settings are saved to battery-backed memory.
• Uset, Iset, Tset and Sset values can be saved.
Settings
(see also page 35)
☞
Select values for the desired parameters.
☞
Press the < SAVE > key.
!
Sto appears at the left-hand display, and the last selected
memory location number appears at the right-hand display.
☞
Select the desired memory location (11 to 255) with the <

>
or the <

> key.
☞
Acknowledge by pressing the < ENTER > key.
Cursor position
SELECT
Setting resolution of
the numeric parameter
CE/LOCAL
Basic Settings
FUNCTION RCL
Uout/Iout
Uset/Iset
FUNCTION
MENU
RCL
MENU
ENTER
SAVE