Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 58 / 114

Share

Page: 58 / 114

Gossen MetraWatt SECULIFE ST PRO Manual Download Page 58

58

GMC-I Messtechnik GmbH

8.7.5

Patient Leakage Current – IP

Definition

Patient leakage current is the current which flows to ground or PE
from the patient ports at the running device via the patient.
The AC and the DC component of the current is measured.

Direct Measuring Method
–

Measurement type: direct P1

– DUT mains plug (PC1) connected to test socket
– Probe to P1 terminal

Schematic Diagram

After activating test voltage, patient leakage current is measured
at the DUT (test probe P1) between PE (DUT mains plug) and the
short-circuited applied parts.
Power is supplied to the DUT via the test instrument. The device
under test (PC1) is operated with mains power.
The measurements must be performed with mains plug polarity in
both directions. Polarity is reversed with the

NL/LN

key.

Measurements are conducted with fixed fault condition

Normal

State

.

Wiring Diagram

– Special Case, Single Fault: Voltage at Applied Parts

Schematic Diagram

Wiring Diagram

Direct Measuring Method
–

Measurement type: direct APP

– DUT mains plug (PC1) connected to test socket
– APPs to APP sockets
– Probe to P1 terminal

Schematic Diagram

After activating test voltage, patient leakage current is measured
between PE (DUT mains plug) and the applied parts connected to
the APP sockets at the test instrument.
Power is supplied to the DUT via the test instrument. The device
under test (PC1) is operated with mains power.
The measurements must be performed with mains plug polarity in
both directions. Polarity is reversed with the

NL/LN

key.

Accessible conductive parts which are not connected to the
housing must be contacted with test probe P1.
Measurements are conducted with fixed fault condition

Normal

State

and test condition

None

.

Wiring Diagram

Single measurements,

rotary switch level: green

Sw

it

ch

Po

si

ti

o

n

Measure-
ment Type
With Mains
to Test
Socket

Measure-
ment Type
Without
Mains
to Test
Socket

Measuring Functions

I

P

Direct P1

I

P

Patient leakage current,

TRMS
I

P~

AC component

I

P=

DC component

U

LPE

Test voltage

Direct APP

Perm. conn. P1

Perm. conn.
APP

I

P

«
...
56
57
58
59
60
...
»

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments