Gorgy Timing LEDI NETWORK TDS GPS RAIL DIN TH 35 User Manual Download

Page: 95 / 101

MDE-LEDI-NETWORK-TDS-4099V3.0

8.2. MICROCONTROLLERS REPLACEMENT

Tools:

►

Torx T15 screwdriver: front face (rack) or tip plate (case)

►

Torx T10 screwdriver: lid (rack) + front face (case) + output cards

►

PLCC extractor: microcontroller

►

Gorgy Timing reference: CIS8951RC2P

►

Unplug every cable at the back of the product

►

Remove the four M3.5 screws from the front face

►

Remove the six M3 screws from the lid

►

Use the PLCC extractor to remove the microcontroller

►

Insert the new Microprocessor, making sure to match the indexing slots

☛

On one side of the micro there is a point (marked 1). Make sure that the support

arrow (marked 2) is on the same side as the point.

Note: the system has 2 indexing slots:

The bevelled corner of the micro must face one of the bevelled corners of the support.

Summary of Contents for LEDI NETWORK TDS GPS RAIL DIN TH 35






































































































Search results

Summary of Contents for LEDI NETWORK TDS GPS RAIL DIN TH 35

Reviews:

Related manuals for LEDI NETWORK TDS GPS RAIL DIN TH 35

Brands by name

Popular brands

Gorgy Timing LEDI NETWORK TDS GPS RAIL DIN TH 35, User Manual

Search results

Summary of Contents for LEDI NETWORK TDS GPS RAIL DIN TH 35

Reviews:

Related manuals for LEDI NETWORK TDS GPS RAIL DIN TH 35

Brands by name

Popular brands