background image

INSTALLATION & OPERATING

INSTRUCTIONS for

GPG10 & GPG12

SINGLE PACKAGE GAS-ELECTRIC

HEATING & COOLING UNIT

Affix this manual and Users Information Manual adjacent to the unit.

US

This Forced Air Central Unit Design Complies With

Requirements Embodied in The American National
Standard / National Standard of Canada Shown Below.

ANSI Z21.47-CSA-2.3 Central Furnaces

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

ATTENTION INSTALLING PERSONNEL

Prior to installation, thoroughly familiarize yourself with this Installation Manual. Observe all safety warnings. During

installation or repair, caution is to be observed.

It is your responsibility to install the product safely and to educate the customer on its safe use.

These installation instructions cover the outdoor

installation of single package gas electric heating and
cooling units. See the Product Data Book applicable to

your model* for information regarding accessories.

'NOTE: Please contact your distributor or our

website for the applicable product data

book referred to in this manual.

10-245

Goodman Manufacturing Company, L.R

2550 North Loop West, Suite 400, Houston, TX 77092

www.qoodmanmfg.com

©2004 Goodman Manufacturing Company, L.R

6/04

Summary of Contents for GPG10





















Reviews: