Required/ Nécessaire/ Obligatorio
Hardware kit* / Trousse de quincaillerie* /
Kit de aditamentos*
WARNINGS AND CAUTIONS
Plug-In 5CCT LED Under Cabinet Dimmable Bar w/ USB Ports
(Page 1)
Barre d’éclairage enfichable 5CCT à DEL à intensité lumineuse variable en dessous d’un
meuble avec ports USB
(Page 3)
Barra de luz LED enchufable 5CCT de intensidad regulable para debajo de gabinetes con
puertos USB
(Página 5)
* Actual hardware may differ from illustration.
* La quincaillerie incluse peut être différente de l’illustration.
* Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
IMPORTANT SAFETY INFORMATION
1. Use
ONLY
insulated staples or plastic ties to secure the cords.
2. Route and secure the cords so that they will not be pinched or damaged.
3. LED light output is strong enough to injure human eyes. Do
NOT
look directly at
exposed LEDs.
4. LEDs gradually emit less light over their lifetime.
5. Do
NOT
use with an extension cord, use
ONLY
with power strips that have integral
overcurrent protection.
6. Do
NOT
mount to surfaces less than ¼ in.
7.
A. For installation with Command
®
Strips by 3M:
Do
NOT
mount over sinks,
stoves, beds or inside of enclosed cabinets. Do
NOT
mount on wallpaper.
B. For installation using screws:
Do
NOT
mount over sinks, stoves, or inside of
enclosed cabinets.
8. Turn power off before servicing.
9. Maximum number of fixtures per run must not exceed maximum power supply
wattage rating of 240W.
10.
NOT
intended for recessed installation in ceiling or soffits.
11. Suitable for
INDOOR
damp locations
ONLY
.
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
CAUTION: DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT.
Model / Model / Modelo #:
UC1270-WHG-12LFC-G,UC1270-WHG-18LFC-G, UC1270-WHG-24LFC-G
Diffuser
Diffuseur
Difusor
5 Light Settings Button
Bouton de réglage de l’éclairage (5 options)
Botón de 5 ajustes de luz
ON/OFF Dimming switch
Interrupteur pour allumer ou éteindre le
luminaire permettant de varier l'intensité lumineuse
Interruptor regulador de ENCENDIDO Y APAGADO
USB ports
Ports USB
Puertos USB
CCx4
CCx5
CCx5
CC
CC
DD
linking cord
Cordon de raccordement
Cable de enlace
Plug-in Driver
Support du luminaire
Bandeja de la lámpara
Easy Installation Command
®
Strips by 3M
1
2
NOTE:
Ensure mounting location is within 5ft. of an electrical outlet. Clean surface with rubbing alcohol. Remove red liners. Press two
strips
(CC)
to the back of the fixture on each end for 12” bar. Apply additional strip
(CC)
in the middle for 18” and 24” bars. Remove
black liners. Press the fixture to surface with tab towards you. Press firmly for 30 sec.
Use the 2 included clear cord clips
(DD)
for cord management. To apply, clean surface with rubbing alcohol. Use the 2 additional strips
(CC)
for cord clips
(DD)
. Remove red liners. Press the strips to the back of the clip. Remove black liners. Press each clip firmly to the
surface for 30 sec. Insert cords into cord clips and plug into outlet.
1
2
seconds
30
REMOVAL
Gently hold the light or clip in place with one hand. Never pull the strip away from the surface! Always pull along the surface. Slowly stretch
each strip slowly against the surface at least 6 inches to release.
SLOWLY
This LED Light bar has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will only fit in
a polarized outlet one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use
power strip unless the plug can be fully inserted. Do not alter the plug.
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
UC1270-WHG-12LFC-G
UC1270-WHG-18LFC-G
UC1270-WHG-24LFC-G
BBx4
BBx4
BBx4
UC1270-WHG-12LFC-G
UC1270-WHG-18LFC-G
UC1270-WHG-24LFC-G
AAx2
AAx2
AAx2
UC1270-WHG-12LFC-G
UC1270-WHG-18LFC-G
UC1270-WHG-24LFC-G
DDx2
DDx2
DDx2
UC1270-WHG-12LFC-G
UC1270-WHG-18LFC-G
UC1270-WHG-24LFC-G
seconds
30
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
1. Verifique que el interruptor de la fuente de alimentación y de la
luz están en la posición de encendido.
2. Pruebe o reemplace el interruptor.
