5
4
Español
FF x1
EE x1
1
B
1
C
1
A
AA x2
GND
1
1
2
2
3
1
2
1
A
1
B
1
C
5
Presione el centro del difusor mientras desliza un extremo en un capuchón.
Mueva el otro extremo en el capuchón opuesto hasta que el difusor se
asiente por igual en cada capuchón. Restablezca la alimentación.
Empuje con cuidado el difusor cerca de un extremo y deslice el difusor en un capuchón hasta que el otro extremo del difusor salga por el otro capuchón. Retire el difusor.
Identifique los orificios roscados en el soporte de montaje universal (
EE
) al alinear con los orificios de montaje de la bandeja de la lámpara. Fije los tornillos de
montaje (
AA
) de la lámpara en los orificios roscados y deje que se extiendan aproximadamente 9,52 mm. Fije el soporte de montaje a la caja eléctrica con los
tornillos de la caja eléctrica existente .
Pase los cables de la lámpara a través del orificio cerca del centro de la bandeja de la lámpara hasta la parte posterior de la lámpara. Con la cadena de soporte (
FF
),
conecte un extremo a la parte posterior de la bandeja de la lámpara cerca del centro en las ranuras especialmente diseñadas. Enganche el otro extremo de la cadena
de soporte a la caja eléctrica para sostener temporalmente la lámpara para conectar el cableado.
1
2
1
2
3
Retire la cadena de soporte. Inserte la cabeza del primer tornillo en la ranura
con forma de cerradura recta , gire la lámpara y pase el segundo tornillo
en la ranura con forma de cerradura curvo . Una vez que los tornillos
estén instalados, coloque la lámpara en la posición deseada. Apriete
los tornillos.
2
2
Good Earth Lighting
®
is a registered trademark of Good Earth Lighting, Inc. All rights Reserved.
Distributed by:
Good Earth Lighting
®
1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Fixture doesn’t light.
Problem
Cause
Solution
Fuse blows or circuit breaker trips
when light is turned on.
Power is off.
Bad connection.
Bad switch.
Discontinue use.
Check if power supply is on.
Check cords and/or wiring.
Test or replace switch.
Call Customer Service Center
1-800-291-8838.
Before doing any work on the fixture, shut off power supply at the circuit breaker panel
to avoid electrical shock.
Hardware Kit:
ZH-AC1050F01-AL3
Replacement Parts List
SAVE THESE INSTRUCTIONS.
Troubleshooting Guide
Printed in China
English
6 YEAR LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original
purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential
environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has
been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original
purchase receipt showing date of purchase. Call
1-800-291-8838
to obtain a return authorization number and an address where to ship your defective
product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture
product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the
liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential
in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or
repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications
to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1)
Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a
circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
1
2
3
1
2
5
3
4
SHOCK WARNING:
Do not install the expansion kit to the starter kit unless POWER is OFF. The mounting rings may be pre-installed on the top of the pucks. If so, rotate them
counterclockwise and remove.
Locate the mounting location where the pucks will be mounted and mark the center location of each puck. Once the center points of the pucks have been determined, hold each
mounting ring in place and mark both holes.
Either dimple the surface with an awl or nail, or drill small pilot holes for the screws. Attach the mounting rings with the two screws.
4
5
6
Once the mounting ring is secure, bring the puck to the mounting ring and engage two of the four tabs on the puck into the two catches molded into the ring and turn clockwise.
Up to 6 puck lights can be connected to the power control unit of the
#AC1050-AL3-03LF3-G
puck light kit. Connect each additional puck light by inserting the plug from the
add-on puck light into the open connector of the last installed puck light.
Any excess hanging cord can be secured using the cord mounting clip provided. Use caution when attaching the cord mounting clip to the cabinet to ensure the metal nail does
not pierce the cord. Restore power and the installation is complete.
Mounting Instructions
6
Model / Modèle / Modelo #: LF1086-BR4-32LF2-G
32 in. Portal LED Flush Mount Ceiling Fixture
(Page 2)
Plafonnier encastré à DEL Portal de 81,28 cm
(Page 3)
Lámpara LED de techo de instalación al ras Portal de 81,28 cm
(Página 4)
English
GND
CC
x1
EE
x1
AA
x4
BB
x2
DD
x2
FF
x1
*Actual hardware may differ from illustration
* La quincaillerie incluse peut être différente de l’illustration.
*Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
Hardware kit / Trousse de quincaillerie/ Kit de aditamentos
Required / Nécessaire/ Obligatorio
Diffuser
Diffuseur
Difusor
Fixture Pan
Support du luminaire
Bandeja de la lámpara
Locking Tab
Languette de verrouillage
Lengüeta de empalme
Français
Avertissements et mises en garde (Page 1)
Installation du Luminaire (Page 3)
Liste des Pièces de Rechange (Page 3)
Guide de Dépannage (Page 5)
Garantie de Good Earth Lighting
®
(Page 6)
English
Warnings and Cautions (Page 1)
Fixture Installation (Page 2)
Replacement Parts List (Page2)
Troubleshooting Guide (Page 5)
Good Earth Lighting
®
Warranty (Page 6)
