background image

14" COLOUR DISPLAY UNIT - CDU

1435SE/GS11

This unit is manufactured by GOLDSTAR and bears the marking CDU 1435S/GS11 on the rear
and DSM 27-039 on the Progetto di Gestione.
It can display 5 different vertical resolution: 350, 400, 480 lines (VGA standard mode); 600 lines
(Super VGA mode) and 768 lines (1024 x 768 interlaced mode). Vertical scan frequency varies
from 56 to 87 Hz. (Interlacing frequency). 
The horizontal scan frequency may be of: 31.5 KHz (VGA standard mode); 35.2 KHz (Super VGA
mode) or 35.5 KHz (1024 x 768 interlaced mode).

CHARACTERISTICS

Ergonomic, high resolution, VGA-compatible, analog video.

Screen dimensions:

14"

Horizontal dimension: 

240 mm 

±

 6 mm

Vertical dimension:

180 mm 

±

 3 mm

Input voltage:

110 V: 98 - 132 Vac for CDU 1435SE/GS11 - 110 V
220 V: 198 - 264 Vac for CDU 1435SE/GS11 - 220 V

Mains frequency:  

50 

±

  3 Hz - 60 

±

  3 Hz

Degauss:

On powering up

Horizontal Synchronism:
Frequency:

31.5 - 35.2 - 35.5 KHz 

Polarity:    

Negative or positive

Level:

        

TTL

Pull-in range:

more than 

±

 250 Hz

Hold-in range: 

more than 

±

 350 Hz

Retrace period:

5.0 

µ

s max.

Vertical Synchronism:
Frequency:

56 - 60 - 70 - 87 (Interlaced) Hz

Polarity:    

Negative or positive

Level:  

TTL

Pull-in range:

50 - 87 Hz

Hold-in range: 

50 - 87 Hz

Retrace period:

< 800 

µ

s

Input signals:
Video:

R, G, B (Red, Green, Blue) driving

Signal: 

Linear voltage steps (63 steps of 11 mV)

Level:  

0 - 700 mV

Polarity:           

Positive

Resolutions displayed:   

640 x 350 rows x columns ( VGA standard mode)

640 x 400 rows x columns (VGA standard mode)
640 x 480 rows x columns (VGA standard mode)
800 x 600 rows x columns (Super VGA mode)
1024 x 768 rows x columns (1024 x 768 int. mode)

External Controls:

Brightness - Contrast 
Horizontal size - Vertical size
Horizontal phase - Vertical center 

20

Video Unit - Pocket Service Guide

14" COLOUR DISPLAY UNIT - CDU 1435SE/GS11

20-1

Summary of Contents for CDU 1435SE/GS11











Reviews: