© by GLOBAL GARDEN PRODUCTS
72FL hydro
ii
.
1
INTRODUCTION
1 / 1
쑮
쑮
쑱
쑱
WORKSHOP MANUAL
pag.
MODEL YEAR 2016
INTRODUCTION
This manual has been compiled to help Service Cen-
tres with the maintenance, dismantling and repair of
the following versions of the 72FL-Hydro
Each page of this manual states the following infor-
mation:
A)
Machine or machine series to which the page
ap plies.
B)
Page number, specifically:
– the first two figures separated by a point indi-
cate the section and the chapter
– the third figure indicates the modification in dex.
C)
Temporary validity of the page, with reference to
the year of manufacture or serial numbers.
D)
Date of release.
E)
Page number and total number of pages dedi-
cated to the subject.
F)
Any previous or ensuing pages dedicated to the
sub ject.
G)
Any chapters before or after the current one.
The manual refers to the following symbols:
Warns of operations that should be carried
out with utmost care to avoid impairing the func-
tionality and safety of the lawnmower.
Warns of operations that should be carried
out with utmost care to avoid injury to the ope -
rator.
Reference to another procedure or part of
the manual.
This symbol highlights all those operations
that require different working methods depen -
ding on the type of machine, subsequent modifi-
cations or accessories fitted.
NOTE
Whenever a reference is made to a position on the
machine “front”, “back”, “left” or “right” hand side, this
is determined by facing the direction of forward travel.
The manual has left out the simplest and quickest op-
erations that can be handled by a good mecha nic,
while concentrating more on specific aspects and
the best servicing procedures.
You are asked to read through this manual to ac quire
a basic understanding of the machine, which is nec-
essary for working rationally without making errors or
wasting time.
All problems related to use are fully covered in the u -
ser manual.
3/2015
5.6 REMOVAL OF THE ENGINE
Since there are different types of drive, the stages
de scribed here refer to those shared or similar in all
types of engine.
Turn back the wheels cover [see 2.5].
Disengage the blade to loosen the belt. The trans-
mission belt should also be loosened.
This is done by ...
➤
➤
mechanical drive models:
engaging the parking brake.
➤
➤
hydrostatic drive models:
releasing the spring (1) of the stretcher.
Undo the central screw (2) and take out the pulley (3)
from the shaft.
If it is difficult to take out, use the special extractor in -
serted into the holes (4) of the pulley, but do not com -
pletely undo the screw (2) so that the extractor puts
pressure on the head of the screw and does not
damage the threaded hole of the shaft.
Remove the protection from the exhaust (5) (diffe ring
according to the types of engine), and disconnect the
accelerator cable control and all the electrical wires.
Close the fuel cock and detach the fuel pipe,
taking
care not to spill fuel.
Find and undo all the screws holding the engine to the
frame, grip the engine firmly and lift it, taking the nec-
ess ary care bearing in mind that its weight is around
25 - 35 kg.
NOTE
Some types of engine are held with screws of differ-
ent lengths and in different positions, so it is best to
label them so that no errors are made when reas sem -
bling.
3/2013
72FL hydro
5.6
.
0
REMOVAL OF THE ENGINE
씱
씱
씱
씱
씰
씰
씰
씰
1 / 2
쑮
쑮
쑱
쑱
WORKSHOP MANUAL
pag.
from
2013
to
••••
© by GLOBAL GARDEN PRODUCTS
5
2
4
3
1
A
C
F
E
F
D
G
B
G
<= ...BACK... <=
