background image

 

Page 

14

 of 

21

 

 

Running Dante Controller 

 
At the time of writing this manual the Dante Controller looks as per the screenshot 
below: 
 

 
 
The AOIP2M will have been named at the factory during test to allow them to be 
identified by the Dante controller. 
 
The format used for the factory name is: 
 

AOIP2M-SN-

XXXX’

 

 

Where ‘

AOIP2M

’ 

refers to the Glensound product i.e. AOIP2M 

 

The ‘SN

-

XXXX’ refers to the serial numb

er of the AOIP2M which can be found printed 

on the rear or side of the unit. 
 

The unit may be renamed in Dante controller by opening the ‘Device view’ window and 

selecting AOIP2M in the drop-

down menu. Go to the ‘Device Config’ tab and change 

the name with the Rename Device box. 
 
Note if you upload a new DNT file or clear the devices config then the name will change 

to ‘

AOIP2M-

xxXxXx’ whereby the ‘X’s refer to the devices MAC address. 

 

  

Dante Controller TIP 

 
If you have never run Dante controller before then make sure that on the bottom left of 

the Dante controllers’ screen ‘P’ or ‘S’ is next to a green square as this indicates that it is 
connected to a network. By clicking ‘P’ or ‘S’ a pop up box opens to allow you to set 

what network interface the controller is using.  
 

 

 

Summary of Contents for Dante AOIP2M






















Reviews: