PACKAGE CONTENTS
•
1 x D-TECT Dual ABS
•
1 x Drilling template for fixing holes
•
3 x 31.75mm wall plugs
•
3 x 31.75mm screws
•
2 x Spare sliding curtains
•
2 x Tamper feet
•
1 x Installation manual
•
1 x Creep mirror
INTRODUCTION
The D-TECT Dual ABS is an outdoor motion detector and
alarm trigger that uses two independent passive infra-red
detectors plus a microwave sensor module. All three
sensors must trigger to cause the detector to signal an
alarm. Utilising triple detection technology, the D-TECT
Dual ABS delivers precise, reliable presence detection.
QUICK INSTALLATION
1.
Mount and connect the detector following the
instructions given later in this sheet.
2.
Apply supply voltage to the unit. The detection LED
(blue) flashes three times.
3.
Wait approximately 2 to 3 minutes to allow the
detector to settle.
4.
Press the programming button once to activate walk
test mode. The detection LED is now enabled for
five minutes.
Note: The front cover must be fitted
when walk testing.
The default settings are:
•
Range: 30 meters
•
Pulse count: 1 (always set to 1 during walk rest)
•
Detection LED: off (always enabled during walk test)
MOUNTING THE UNIT
During installation, protect the electronics against water, as
trapped moisture can affect or damage the unit.
WARNING
• NYLON WASHERS PROVIDED MUST BE USED WITH SCREWS
• ENSURE CABLE ENTRY AND SCREW HOLES ARE
SEALED WITH WATER BASED SEALANT
• DO NOT USE SILICONE BASED SEALANT
To reduce the possibility of the microwave circuit being
affected it is recommended to leave a minimum space of 3
metres between D-TECT Dual ABS sensors when mounted
alongside each other. When facing each other a minimum
space of 15 metres is recommended. It is possible to
mount the units back to back however when detectors are
mounted in close proximity to one another it is advisable to
carry out a walk test to ensure that external objects are not
influencing the microwave circuit.
1.
Drill the wall to accept the two fixing screws, the
cable entry, and the tamper cup (if used). See
Figures 1 and 2. A hole-drilling template is provided.
Note: We recommend using the tamper cup on
uneven wall surfaces.
2.
Remove the cover assembly by loosening the locking
screw using the allen key provided. The cover hinges
from the top and lifts out of the location slot. See
Figure 3.
3.
Feed standard eight-core alarm cable into the cable
entry. Bare the wires and connect to the terminal
block. See Figures 2, 4, 5, 6 & 7.
4.
Screw the unit to the wall ensuring that the
tamper pin is correctly located and that the tamper
microswitch is closed. See Figure 7. To aid
installation, two spare tamper feet are provided. One
is 1mm longer and the other is 2mm longer than the
tamper foot originally fitted. The tamper foot is a push
fit and can be removed by carefully pulling it from the
pin. See Figure 2.
5.
When the detector is aligned, connected, and
programmed to suit the installation, replace the front
cover and lock as shown. See Figure 8.
MULTIBEAM ALIGNMENT & MASKING
The multifunction lens fitted to D-TECT Dual ABS produces
seven long range beams and seven medium to short range
curtain PIR beams. The PIR circuitry detects changes in
heat and movement in the beam pattern; therefore items
such as trees, shrubs, ponds, boiler flues, and animals
should be considered when positioning the detector.
Note: The PIR sensor is more sensitive to movement
across the beams, and less sensitive to movement
directly towards or away from the beams.
The detector module is fitted with two sliding shutters to
reduce the detection angle.
The curtains are fitted to the pan and tilt module as shown
in Figure 9 (shown with primary and additional curtain
sliders fitted). Each section of the detector lens gives a
coverage pattern of approximately 10 degrees.
An additional set of curtain sliders is provided should the
beam pattern need to be narrowed even further, e.g. if the
minimum detection angle of 10 degrees is required.
When coverage exceeds the desired detection area, adjust
the module as required and mask off any beams, either
vertically or horizontally, to avoid unwanted detection.
Use portions of the self-adhesive silver mask applied to the
rear, smooth side of the lens as shown in Figures 10 & 11.
Always replace the lens the correct way up to ensure exact
beam pattern coverage (top of the lens is marked TOP).
When mounted at heights above 3 metres there could be a
significant reduction in the range of detection and the target
will have to move a greater distance within the field of view
before an alarm is generated.
1
D-TECT Dual ABS
GJD365 ABS External Detector
Detect
.
Illuminate
.
Deter
