Girard Systems 98GC229 Installation Manual Download Page 4 | Manualshive

Page: 4 / 11

background image

Page 4 of 11

PRODUCT DESCRIPTION

The 98GC229 is a Single channel RF transmitter, powered by two 3v Lithium batteries

(CR2032) designed to control a single Awning by means of three push buttons. IN,

STOP and OUT. As displayed in the picture below.

The faceplate can be removed easily by holding the module at the left and right edges

firmly in one hand and push the STOP button with two fingers of your other hand. The

picture below shows how the batteries must be inserted.

«
...
2
3
4
5
6
...
»

Summary of Contents for 98GC229












Reviews:

No comments

Related manuals for 98GC229

MMAC-Plus 9G426-02

Brand: Cabletron Systems Pages: 12

MMAC-Plus 9F310-02

Brand: Cabletron Systems Pages: 4

Brand: Cabletron Systems Pages: 16

Brand: cable matters Pages: 4

Brand: CableCreation Pages: 7

Brand: Datavideo Pages: 2

Brand: KanexPro Pages: 16

ePowerSwitch 8M+R2

Brand: Neol Pages: 74

EdgePoint EP-S16

Brand: Ubiquiti Pages: 22

StorageWorks SAN Switch Integrated/32

Brand: Compaq Pages: 104

Crocodile Tail Loop

Brand: One Control Pages: 9

Hi-Speed USB 2.0 Hub

Brand: Saitek Pages: 14

Brand: SMART-AVI Pages: 2

COMMANDE MURALE RTS

Brand: SOMFY Pages: 2

Brand: Lindy Pages: 2

Brand: TRENDnet Pages: 7

Champion SeriesKD-2x1CSK

Brand: Key Digital Pages: 6

OBERON C SOUND HUB COMPACT

Brand: Dali Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands