manualshive.com logo in svg

Gira DALI Gateway, Product Documentation, Page: 63 / 136

Share
Download
Gira DALI Gateway Product Documentation Download Page 63

 

"DALI Gateway C00CX2 EN / C00CX4 EN" software 

Functional description 

 

 

Best. Nr. 1060 00 

Page 63 of 136 

 

 

Setting the cyclical transmission function for the switching status feedback telegram 

In addition to being transmitted in case of an update, the switching status feedback telegram can also 
be transmitted cyclically via the active message object. 

„

  Set the “Cyclical transmission of feedback telegram?” parameter in the "Groups - [x] group name - 

switching" to „Yes“. 

Cyclical transmission is now activated. 

„

  Set the “Cyclical transmission of feedback telegram?” parameter in the "Groups - [x] group name - 

switching" to „No“. 

Cyclical transmission is now deactivated which means that a feedback telegram is transmitted to the 
bus only if one of the switching states has been updated. 

 

 The cycle time is defined centrally for all DALI groups in the “Groups” parameter node. 

 During an active delay time, no feedback telegram will be transmitted even if a switching state has 

changed. 

 
 

Activating brightness value feedback 

The brightness value feedback can be used as an active message object or as a passive status object. 
In case of an active message object the brightness value feedback telegram will also be directly 
transmitted to the bus after each update. As a passive status object, there will be no telegram 
transmission after an update. In this case, the object value must be read-out. The ETS automatically 
sets the object communication flags required for proper functioning. 
The “Brightness value feedback ?” parameter is separately created for each DALI group in the “Groups 
- [x] group name - dimming" parameter node. 

„

  Set parameter to “Yes, feedback object is now active message object” 

The “Brightness value feedback” object will be enabled. The brightness value will be transmitted 
once it has been updated. After a bus/ mains voltage return or after programming with the ETS, a 
feedback telegram will be automatically transmitted. 

„

  Set parameter to “Yes, feedback object is passive status object” 

The “Brightness value feedback” object will be enabled. The brightness value will be transmitted only 
if the feedback object is read-out by the bus. After bus voltage return or after programming with the 
ETS, there will be no automatic transmission of the feedback. 

 

Summary of Contents for DALI Gateway









































































































































Reviews:

No comments