manualshive.com logo in svg

Gira DALI Gateway, Product Documentation, Page: 13 / 136

Share
Download
Gira DALI Gateway Product Documentation Download Page 13

 

Fitting, electrical connection and operation 

 

 

Best. Nr. 1060 00 

Page 13 of 136 

 

 

Priorities 

The DALI Gateway distinguishes between different functions that can affect a DALI group. In order to 
prevent conflicting output states, each available function has been assigned a certain priority. The 
function with the higher priority overrides the one with the lower priority. 

–

  1

st

 Priority: Manual control mode (highest priority) 

–

  2

nd

 Priority: Forced-control position or disable function 

–

  3

rd

 Priority: Direct bus mode (“Switching” & “Dimming” & “Brightness value” objects, scenes, centra 

function) 

 
 

Switching on the temporary manual control for the broadcast function 

The manual control for the broadcast function can be utilized while the DALI Gateway is in the 
unprogrammed state. As in this case no group configurations have been stored due to a missing ETS 
programming, the DALI Gateway will collectively control the connected DALI devices in manual control 
per broadcast command.  

The DALI Gateway has not yet been programmed via the ETS. 

„

  Press the   key briefly (< 1 s). 

"

" is shown on the 7-segment display. 

 After 5 s without key-press, the Gateway will deactivate the manual control for the broadcast. 

 The Gateway is delivered with the broadcast mode activated. After programming via the ETS, it is 

also possible to reactivate the broadcast mode any time by unloading the application program via the 
ETS. 

 
 

Switching on the temporary manual control for broadcast 

The DALI Gateway has not yet been programmed via the ETS. 

Temporary manual control mode for the broadcast has been activated. 

„

  No key-press for 5 s 

- or - 

„

  Press   key twice. 

- or - 

„

  Switch off mains voltage supply.  

Temporary manual control mode for broadcast has now been terminated. The 7-segment display will 
extinguish. 

 When shutting off the temporary manual control mode for broadcast, the state selected by manual 

control will not change. 

 
 

Switching on permanent manual control mode for broadcast 

The DALI Gateway has not yet been programmed via the ETS. 

Manual control mode or temporary manual control mode for broadcast has not been activated. 

„

  Press the   key for at least 5 s. 

The   status LED is illuminated. "

" is shown on the 7-segment display. Permanent manual 

control mode for broadcast has been activated 

Summary of Contents for DALI Gateway









































































































































Reviews:

No comments