Gilson Quad-Z 215 Page 23 User Manual Download

Page: 23 / 112

2-7

Installation

Plumbing Connections

Transfer Tubing Installation

1 Connect one end of each piece of transfer

tubing to the 444 QuadDilutor. Refer to the 444

QuadDilutor User’s Guide for more information.

2 Locate the level sensing cables (LLD cables)

supplied with the Z-arm.

3 Pass the other end of each transfer tubing

through the open end of an LLD cable casing

nearest the right-angle connector. The tubing

should exit the back of the LLD cable casing

approximately 6.5 cm from the end.

4 Connect each tubing to the top of the isolation

probe holder using a 1/4"-28 nut and ferrule

supplied with the tubing. Firmly tighten this

fitting using the supplied headless nut extender

(part number 49041032) since it holds the probe

in place.

Summary of Contents for Quad-Z 215
















































































































Search results

Summary of Contents for Quad-Z 215

Reviews:

Related manuals for Quad-Z 215

Brands by name

Popular brands

Gilson Quad-Z 215, User Manual

Search results

Summary of Contents for Quad-Z 215

Reviews:

Related manuals for Quad-Z 215

Brands by name

Popular brands