background image

W

AR

R

AN

T

Y

24

WARRANTY

 

PIPETMAN® CLASSIC

Chapter 9

WARRANTY

Gilson warrants this pipette against defects 

in material under normal use and service for a 

period of 

three years

 from the date of purchase.

This warranty shall not apply to pipettes which 

are subject to abnormal use and/or improper 

or inadequate maintenance (contrary to the 

recommendations given in the user’s guide), 

including, but not limited to pipettes which have 

been subjected to physical damage, improper 

handling, or spillage or exposure to any corrosive 

environment. This warranty shall also be void 

in the event pipettes are altered or modified by 

any party other than Gilson or its designates. 

Gilson’s sole liability under this warranty shall 

be limited to, at Gilson’s sole option, repair, or 

replacement of any defective components of 

pipettes or refund of the purchase price paid for 

such pipettes. 

Routine cleaning, control, and 

recalibration are not covered under the warranty.

The replacement of wearing parts such as seals, 

o-rings, broken pistons assembly, and broken tip 

holders are not covered under the warranty.

NOTICE

Yearly routine maintenance is highly 

recommended to keep your pipette in 

good condition, ensuring a continued 

high level of performance. 

Do not lubricate this pipette. The use 

of lubricant cancels the warranty of 

this pipette.

THE FOREGOING WARRANTY IS EXCLUSIVE 

AND GILSON HEREBY DISCLAIMS ALL OTHER 

WARRANTIES, WHETHER EXPRESS OR 

IMPLIED, INCLUDING ANY WARRANTIES OF 

MERCHANTABILITY AND ANY WARRANTIES 

OF FITNESS FOR A PARTICULAR PURPOSE, 

UNDER NO CIRCUMSTANCES SHALL GILSON BE 

LIABLE FOR ANY CONSEQUENTIAL, PUNITIVE, 

INDIRECT OR INCIDENTAL DAMAGES ARISING 

OUT OF ANY BREACH OF ANY EXPRESS OR 

IMPLIED WARRANTY.

Summary of Contents for PIPETMAN Classic P10





























Reviews: