manualshive.com logo in svg

Gilera Runner PureJet 50, Manual, Page: 26 / 60

Share
Download
Gilera Runner PureJet 50 Manual Download Page 26

Hub oil level (03_01, 03_02, 03_03)

Remove the oil filler cap/dipstick «

A

» Unscrew the oil filler plug «

B

» and drain out all

the oil. Screw in the drainage cap again and fill the hub with the specified oil.

Characteristic

Rear hub oil

Quantity: approx. 75 cm³

03_01

03_02

Place the vehicle on its stand on a level surface. Unscrew dipstick "

A

", dry it with a

clean rag and then rescrew it completely. Unscrew the dipstick and check that the oil
level reaches the 2rd notch from the bottom of the dipstick. Rescrew the dipstick com-
pletely.

CAUTION

RUNNING THE ENGINE WITH INSUFFICIENT LUBRICATION OR WITH THE IN-
ADEQUATE LUBRICANTS ACCELERATES WEAR AND TEAR OF THE MOVING
PARTS AND CAN CAUSE IRRETRIEVABLE DAMAGE.

USED OILS CONTAIN SUBSTANCES HARMFUL TO THE ENVIRONMENT. TO
HAVE THE OIL CHANGED, CONTACT AN AUTHORISED PIAGGIO SERVICE
CENTRE, WHICH ARE EQUIPPED TO DISPOSE OF USED OILS IN ENVIRON-
MENTALLY-FRIENDLY MANNER AND IN COMPLIANCE WITH THE REGULA-
TIONS IN FORCE.

Recommended products

AGIP GEAR SAE 80W-90

Lubricant for gearboxes and transmissions.

26

3 Maintenance

Summary of Contents for Runner PureJet 50





























































Reviews:

No comments