manualshive.com logo in svg

Gilbarco MDE-3664B, Start-Up, Service And Parts Manual, Page: 59 / 131

Share
Download
Gilbarco MDE-3664B Start-Up, Service And Parts Manual Download Page 59

Major Hardware Components

System Cables

Page 4-38                                                                                                  MDE-3664B TRIND® Start-up, Service, and Parts Manual · June  2013

Full System Cable Connections on MPD-3 Dispensers

For all single-sided units, install Dummy Load Connector (R20526-01) on JB on transmitter 
PCB and skip all Side B connections.

Note: If power is applied to Card Cage without the antenna cables or dummy load connected, 

the transmitter board will be damaged.

On Cable

Connect

To

On

R20509-G2 (marked for Side A)

P1/2

J1

Side A Overhead Antenna (low frequency)

PA/B

*JA

Transmitter PCB Q13564

R20509-G2 (unmarked for Side B)

P1/2

J2

Side B Overhear Antenna (low frequency)

PA/B

*JB

Transmitter PCB Q13564

R20519-G3 (marked for Side A)

J182

P182

Light/Micro Reader PCB Assembly T20182 on Side A Faceplate 
Assembly

P7

*J7

DCB PCB Q13563

R20519-G3 (unmarked for Side B)

J182

P182

Light/Micro Reader PCB assembly T20182 on Side B Faceplate 
Assembly

P8

*J8

DCB PCB Q13563

R20521-G3 (marked for Side A)

J180

P180

Light/Micro Reader PCB Assembly T20182 on Side A Faceplate 
Assembly

J177

*P177

Power Supply PCB T20138

GRD

*Ground Stud Card Cage

R20521-G3 (unmarked for Side B)

J180

P180

Light/Micro Reader Pcb Assembly T20182 on Side B Faceplate Assembly

J176

*P176

Power Supply PCB T20138

GRD

*Ground Stud Card Cage

Q13578-01 -01 (marked for Side A)

P1

J1

Side A Overhead Antenna (high frequency)

P1

*J2B

Receive PCB

Q13578-01 (unmarked for Side B)

P1

J2

Side B Overhead Antenna (high frequency)

P1

*J2A

Receive PCB

R20437-G01

J250

*P250

TI Gateway PCB T20128-G1

J258A

P258

Side A CRIND Logic PCB T17764

J258B

P258

Side BCRIND Logic PCB T17764

R20580-G1

P601

J601

3 prong F

3 prong M

Card Cage, Rear

*Indicates connection point is on Card Cage assembly.

Summary of Contents for MDE-3664B




































































































































Reviews:

No comments