Gilbarco MDE-3664B Start-Up, Service And Parts Manual Download Page 50

Page: 50 / 131

MDE-3664B TRIND® Start-up, Service, and Parts Manual · June 2013

Page 4-29

TRIND Option Doors with Antennas

Major Hardware Components

Encore CIM Door Option Assembly

This section provides the parts for the Encore CIM Door Option Assembly.

Figure 4-30: Encore CIM Door Option Assembly

Hex Head 6-20
Screw

Phillips Screw

TRIND Display
Window Lens

TRIND Panel Gasket

CIM Door with CRIND Assembly

TRIND Light and Indicator Assembly

Encore CIM Door Option Assembly Parts List

Following table lists the Encore CIM Door Option Assembly parts:

Item

Part Description

Part Number

Screw, Hex Head 6-20

Q11677-24

TRIND Light and Indicator Assembly

M01218A00X*

CIM Door with CRIND Assembly

M01208A001

TRIND Panel Gasket

M01160B001

TRIND Display Window Lens

M01234B001

Screw, Phillips

M00419B117

*Order entry item available as red (-A001) or orange (-A002).

Summary of Contents for MDE-3664B




































































































































Search results

Summary of Contents for MDE-3664B

Reviews:

Gilbarco MDE-3664B, Start-Up, Service And Parts Manual, Page: 50 / 131

Search results

Summary of Contents for MDE-3664B

Reviews: