manualshive.com logo in svg

Gilbarco MDE-3664B, Start-Up, Service And Parts Manual, Page: 18 / 131

Share
Download
Gilbarco MDE-3664B Start-Up, Service And Parts Manual Download Page 18

MDE-3664B TRIND® Start-up, Service, and Parts Manual · June 2013

Page 3-1

Full Systems

Systems Overview

3 – Systems Overview

Full Systems

The Full System product is an option available as a retrofit kit or factory installed equipment 
on The Advantage Series, Multi Product Dispenser (MPD-3), Encore, and Eclipse lines of fuel 
dispensers. The TRIND device is connected to the CRIND through a gateway or serial 
interface board. In this application TRIND is a software slave to the CRIND and the associated 
POS controller/host. This means that a properly working TRIND system will look for and read 
tags, but only when told to by the controller, through the CRIND application. 

This system is to be installed in accordance with all Underwriters’ Laboratory (UL), Federal 
Communications Commission (FCC), federal, state, and local regulations associated with it. 
The following illustrations depict the system component used in the Original, The Advantage 
Series, MPD-3, and Encore Full Systems.

Figure 3-1: Original Full System Block Diagram

Overhead Antenna Assembly

Side A

T20231-G1

LF Transmitter (134kHz Intentional

Radiator)

Q13579-01

Control  Data

UHF Receiver Module

902 - 928 MHz

115 VAC

(FROM Dispenser

AC POWER

DISTRIBUTION)

RS-232

RS-232

Gateway Board

T20128

SERIAL DATA

to CRIND logic boards

(Dispenser Electronics)

J7

J8

J4

P187

P250

P185

22VDC,

5VDC, GND

5VDC,

GND

22VDC,

5VDC, GND

J6

J3

22VDC, 5VDC, GND

22VDC, 5VDC, GND

J5

J5

J2A

J2B

JA

JB

LF TX

UHF RX

Overhead Antenna Assembly

Side B

T20231-G1

UHF RX

LF TX

POWER REGULATING

Circuit Board

T20138-G1

P177

P179

P176

P175

P178

Light Board Assembly

(T20295, T20446)

on Dispenser Bezel Face

 (Side A)

P181

P180,

P182

RS-232, Digital

Control and Light

Control Circuit

P180,

P182

P181

RS-232, Digital

Control and Light

Control Circuit

When overhead antennas are not part of
the product, Dummy Load R20526-G1
plugs into  JA and JB.   J2A and J2B  are
left unconnected.

DATA CONTROL BOARD

Q13563-01 or -02

60VAC

Power Supply

R20600-G1

AC Power

EMC Filter
Q10895-01

Micro-Reader

Q13551-01

(134 KHz

Intentional)

Micro-Reader

Q13551-01

(134 KHz

Intentional)

T20143

Bezel

Antenna

R20522-G2

Cable

T20143

Bezel

Antenna

R20522-G2

Cable

Light Board Assembly

(T20295, T20446)

on Dispenser Bezel Face

 (Side B)

RS-232

LF TX/RX

LF TX/RX

RS-485

Summary of Contents for MDE-3664B




































































































































Reviews:

No comments