GILBARCO VEEDER-ROOT Applause Media System Installation, Service, And Parts Manual Download Page 82

Page: 82 / 102

Page C-10

MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Configuring Site Server IP Addresses for Applause
Media System (when IP Addresses Are Changed)

Configuring Network for Gilbarco Dispenser IP Addresses

Apply Network Settings

To activate Network settings, the required network settings MUST be applied.

IMPORTANT INFORMATION

From the Network Config menu, press

Enter

. The Apply Network Settings screen appears.

Figure C-13: Apply Network Settings

Apply Network Settings

Network settings applied

Cancel = Exit

View Network Settings

From the Networking Config menu, press

Enter

. This option enables to view the currently

applied network settings. The View Network Settings screen appears.

Figure C-14: View Network Settings

View Network Settings

CRIND Side A 000.000.000.000
CRIND Side B 000.000.000.000
SM Server

000.000.000.000

Netmask

000.000.000.000

Gateway

000.000.000.000

Cancel = Exit

Following network settings appear:

• Side A IP Address
• SMART Connect Server IP Address
• SMART Merchandising Server IP Address
• Network Mask
• Gateway Address

Notes: 1) For single side units, CRIND Side B IP address displays what is expected to be the

IP address, not the real IP address.

2) If the SMART Connect option is disabled, then the SC Server IP address will no

longer appear.

Summary of Contents for Applause Media System







































































































Search results

Summary of Contents for Applause Media System

Reviews:

Related manuals for Applause Media System

Brands by name

Popular brands

GILBARCO VEEDER-ROOT Applause Media System, Installation, Service, And Parts Manual

Search results

Summary of Contents for Applause Media System

Reviews:

Related manuals for Applause Media System

Brands by name

Popular brands