Gigaset C580 User Manual Download Page 44

Page: 44 / 53

Customer Care and support

A580-A585 / China EN / A31008-M2006-Y101-1-5D19 / appendix.fm / 26.03.2010

rsion 4, 29.1

.2007

Customer Care and
support

Hotline: 4006 706 007

Questions and answers

If you have any questions about using your
phone, visit us at www.gigaset.com/cn at
any time. The table below contains a list of
common problems and possible solutions.

Gigaset C585 only:

The display is blank.

The handset is not switched on.

Press

and hold

the end call key

The batteries are flat.

Charge or replace the batteries
(

page 9).

Base

flashes in the display.

The handset is outside the range of the base
station.

Move the handset closer to the base sta-
tion.

The base station is not turned on.

Check the base station's mains adapter
(

page 7).

Handset does not ring.

The ringer is deactivated.

Activate the ringer (

page 39).

You cannot hear a ringer/dialling tone from
the fixed line network.

The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.

Please always use the phone cord supplied or
ensure that the pin connections are correct
when purchasing from a retailer
(

page 46).

Error tone sounds after system PIN prompt.

You have entered the wrong system PIN.

Reset the system PIN to 0000 (

page 40).

Forgotten the system PIN.

Reset the system PIN to 0000 (

page 40).

The other party cannot hear you.

You have deactivated the microphone.
The handset is "muted".

Activate the microphone again (

page 23).

The number of the caller is not displayed
despite CLIP.

Calling Line Identification is not enabled.

The caller

should ask the network provider to

release Calling Line Identification (CLI).

You hear an error tone (descending tone
sequence) when inputting.

Action has failed/invalid input.

Repeat the operation.
Watch the display and refer to the user guide
if necessary.

You cannot listen to messages on the network
mailbox.

Your PABX is set for dial pulsing.

Set your PABX to touch tone dialling.

No time is specified for a message in the
answer machine history.

Date/time is not set.

Set the date/time (

page 12).

The answer machine announces "PIN is incor-
rect" during remote operation.

1
.

You have entered the wrong system PIN.

Enter the system PIN again.

2
.

The system PIN is still set to 0000.

Change the system PIN (

page 40).

The answer machine will not record any mes-
sages.

Its memory is full.

Delete old messages.

Play back new messages and delete.

Summary of Contents for C580






















































Search results

Summary of Contents for C580

Reviews:

Gigaset C580, User Manual, Page: 44 / 53

Search results

Summary of Contents for C580

Reviews: