manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

90 

 

 

The  softw are can clear it by w riting 1. 

3 

SECERR 

Secure error flag (If there are no option  bytes) 

If an  invalid  secure  DMP  area is defined  (DMPx_EPAGE>  SECMx_EPAGE),  this  

bit is set and the FMC_DMPx  (x=0,1) modification  is discarded. 

The  softw are can clear it by w riting 1. 

2:1 

Reserved 

Must  be kept  at reset value. 

0 

SECBUSY 

The  Flash is busy   

When  the operation  is in progress, this bit is set to 1. When  the operation  is end or 

an error is generated,  this bit is cleared to 0. 

2.5.9. 

Secure Control register (FMC_SECCTL) 

Address offset: 0x30 

Reset value: 0x0000 0080 

This register can only be  written when the SECBSY and NSBSY are reset. Otherwise, the 

write access stalls till SECBSY and NSBSY are reset. 

This  register is  secure. It  can  be  read  and  written  only by  secure access. A non-secure 

read/write access is RAZ/WI. This register can be  protected against non-privileged  access 

when FMC_PRIV = 1. 

This register has to be accessed by word (32-bit).  

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

SECENDI

E 

Reserved 

SECERRI

E 

Reserved 

SECLK 

SECSTA

RT 

Reserved 

SECMER  SECPER  SECPG 

 

rw 

 

rw 

 

rs 

rs 

 

rw 

rw 

rw 

 

Bits 

Fields 

Descriptions  

31:13 

Reserved 

Must  be kept  at reset value. 

12 

SECENDIE 

End  of operation  interrupt enable  bit 

This bit is set or cleared by softw are. 

0: no interrupt  generated by hardw are 

1: end of operation  interrupt enable 

11 

Reserved 

Must  be kept  at reset value. 

10 

SECERRIE 

Error  interrupt  enable bit 

This bit is set or cleared by softw are. 

0: no interrupt  generated by hardw are 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
IBASE Technology IB952 Series User Manual preview
IB952 Series
Brand: IBASE Technology Pages: 71
Net to Net Technologies UIM-1000T Installation Instructions preview
UIM-1000T
Brand: Net to Net Technologies Pages: 4
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Brand: Hanwha Techwin Pages: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Brand: ZALMAN Pages: 9
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
Commell FS-A79 User Manual preview
FS-A79
Brand: Commell Pages: 36
Aaeon FWS-7150 Manual preview
FWS-7150
Brand: Aaeon Pages: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Brand: Juniper Pages: 196
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Brand: AC Infinity Pages: 24
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
Digi DataFire GO! PRO Manual preview
DataFire GO! PRO
Brand: Digi Pages: 20
Kontron AdvancedTCA AT8901M User Manual preview
AdvancedTCA AT8901M
Brand: Kontron Pages: 76
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
Beckhoff EK1122 Documentation preview
EK1122
Brand: Beckhoff Pages: 84

Brands by name

Popular brands

Load more brands