manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

619 

 

 

This bit is reserved in USART1. 

3 

RXFCMD 

Receive  data  flush command 

Writing  1 to this bit clears the RBNE  flag to discard the received data w ithout 

reading  it. 

2 

MMCMD 

Mute  mode  command 

Writing  1 to this bit makes  the USART  into mute  mode  and sets the RWU  flag. 

1 

SBKCMD 

Send break  command 

Writing  1 to this  bit sets the SBKF  flag and makes  the USART  send a BREAK 

frame, as soon as the transmit  machine  is idle. 

0 

ABDCMD 

Auto baudrate  detection  command 

Writing  1 to this bit issues an automatic  baud rate measurement  command  on the 

next received data frame and  resets the ABDF  flag in the USART_STA T. 

This bit is reserved in USART1 

18.4.8. 

Status register (USART_STAT) 

Address offset: 0x1C 

Reset value: 0x0000 00C0 

This register has to be accessed by word (32-bit) 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

REA 

TEA 

WUF 

RWU 

SBF 

AMF 

BSY 

 

r 

r 

r 

r 

r 

r 

r 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

ABDF 

ABDE 

Reserved 

EBF 

RTF 

CTS 

CTSF 

LBDF 

TBE 

TC 

RBNE 

IDLEF 

ORERR 

NERR 

FERR 

PERR 

r 

r 

 

r 

r 

r 

r 

r 

r 

r 

r 

r 

r 

r 

r 

r 

 

Bits 

Fields 

Descriptions  

31:23 

Reserved 

Must  be kept  at reset value 

22 

REA 

Receive  enable  acknow ledge flag 

This bit,  w hich is set/reset by hardw are, reflects the receive enable  state of the 

USART  core logic. 

0: The USART  core receiving logic  has not been enabled 

1: The USART  core receiving logic  has been  enabled 

21 

TEA 

Transmit  enable  acknow ledge flag 

This bit,  w hich is set/reset by hardw are, reflects the transmit  enable  state of the 

USART  core logic. 

0: The USART  core transmitting  logic has not been enabled 

1: The USART  core transmitting  logic has been  enabled 

20 

WUF 

Wakeup  from Deep-sleep  mode  flag 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Z-Wave RAZBERRY 7 PRO Quick Start Manual preview
RAZBERRY 7 PRO
Brand: Z-Wave Pages: 6
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Brand: Ubiquiti Pages: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Brand: CG Pages: 112
Idis DR-6308P Quick Manual preview
DR-6308P
Brand: Idis Pages: 20
Ubiquiti UniFi LED ULED-AT Quick Start Manual preview
UniFi LED ULED-AT
Brand: Ubiquiti Pages: 16
RAID N8103-134 Setup Manual preview
N8103-134
Brand: RAID Pages: 80
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
VANTAS DPA-S50 Owner'S Manual preview
DPA-S50
Brand: VANTAS Pages: 30
ZALMAN CNPS2005-Plus User Manual preview
CNPS2005-Plus
Brand: ZALMAN Pages: 6
c SwiftreaderX Installation Manual preview
SwiftreaderX
Brand: c Pages: 32
Tektronix 7B87 Instruction Manual preview
7B87
Brand: Tektronix Pages: 143
Z3 Technology FV2K-DCK-1x User Instructions preview
FV2K-DCK-1x
Brand: Z3 Technology Pages: 94
Advantech ARK-10 User Manual preview
ARK-10
Brand: Advantech Pages: 59
Crestron C2N-IO Installation Manual preview
C2N-IO
Brand: Crestron Pages: 2
MSI MS-6970A Manual preview
MS-6970A
Brand: MSI Pages: 57
Crestron STIRP Installation Instructions preview
STIRP
Brand: Crestron Pages: 2
MikroTik nRAYG-60adpair Manual preview
nRAYG-60adpair
Brand: MikroTik Pages: 7
Huawei NIP6320 Quick Start Manual preview
NIP6320
Brand: Huawei Pages: 4

Brands by name

Popular brands

Load more brands