manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

584 

 

 

17.4.5. 

TIMERx registers(x=5) 

TIMER5 secure access base address: 0x5000 1000 
TIMER5 non-secure access base address: 0x4000 1000 

Control register 0 (TIMERx_CTL0)  

Address offset: 0x00 

Reset value: 0x0000 0000 

This register has to be accessed by word (32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

 

15     

  14     

  13     

  12     

  11     

  10     

  9     

  8     

  7     

  6     

  5     

  4     

  3     

  2     

  1     

  0     

Reserved 

ARSE     

Reserved 

SPM 

UPS 

UPDIS 

CEN 

   

  rw     

 

  rw     

  rw     

  rw     

  rw     

 

Bits   

Fields 

Descriptions  

31:8 

Reserved 

Must  be kept  at reset value. 

7 

ARSE 

Auto-reload shadow  enable 

0: The shadow  register for TIMERx_CAR  register is disabled 

1: The shadow  register for TIMERx_CAR  register is enabled 

6:4 

Reserved 

Must  be kept  at reset value. 

3 

SPM 

Single  pulse mode. 

0: Counter  continues after update event. 

1: The CEN  is cleared by hardw are and the counter stops at next update  event. 

2 

UPS 

Update  source 

This bit is used to select the update event sources by softw are. 

0: When enabled,  any of the follow ing events generate  an update interrupt  or DMA  

request:   

The  UPG  bit is set 

The  counter generates an overflow  or underflow  event 

The  slave mode  controller  generates an update  event. 

1: When  enabled,  only counter overflow /underflow  generates an update interrupt or 

DMA  request. 

1 

UPDIS 

Update  disable.   

This bit is used to enable  or disable the update  event generation. 

0: update event enable.  The update event is generate  and the buffered registers are 

loaded  w ith their preloaded  values w hen one of the follow ing events occurs: 

The  UPG  bit is set 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

2N OfficeRoute Quick Manual preview
OfficeRoute
Brand: 2N Pages: 11
2N stargate How To Set preview
stargate
Brand: 2N Pages: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Brand: 2N Telekomunikace Pages: 24
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
Ruckus Wireless SmartZone 3.6 Command Reference Manual preview
SmartZone 3.6
Brand: Ruckus Wireless Pages: 102
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
ZKTeco HVR0402 User Manual preview
HVR0402
Brand: ZKTeco Pages: 68
Alula RE930R LTE M1 Install Manual preview
RE930R LTE M1
Brand: Alula Pages: 4
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Brand: Avocent Pages: 2
Hanwha Techwin Wisenet XRN-6410DB4 User Manual preview
Wisenet XRN-6410DB4
Brand: Hanwha Techwin Pages: 118
Curtiss-Wright GTS/DEC/003 Manual preview
GTS/DEC/003
Brand: Curtiss-Wright Pages: 10
Curtiss-Wright DUCOR-80-40-00 User Manual preview
DUCOR-80-40-00
Brand: Curtiss-Wright Pages: 59
Supermicro SuperServer SYS-510D-10C-FN6P User Manual preview
SuperServer SYS-510D-10C-FN6P
Brand: Supermicro Pages: 96

Brands by name

Popular brands

Load more brands