manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

474 

 

 

Figure 17-31. Pause mode of TIMER0 controlled by enable signal of TIMER2 

TIMER_CK

CNT_REG

CNT_REG

CEN

61

62

63

11

12

13

TRGIF

TIMER2

TIMER0

 

In this example, O0CPRE can also be used as trigger source instead of enable signal output. 
Steps are shown as follows: 

1. 

Configure TIMER2 in master mode and O0CPRE as trigger output (MMS=3’b100 in the 
TIMER2_CTL1 register). 

2. 

Configure the TIMER2 O0CPRE waveform (TIMER2_CHCTL0 register). 

3. 

Select TIMER2 as TIMER0 input trigger source (TRGS=3’b010 in the TIMERx_SMCFG 

register). 

4. 

Configure TIMER0 in pause mode (SMC=3’b101 in TIMERx_SMCFG register). 

5. 

Enable TIMER0 by writing ‘1’ to the CEN bit (TIMER0_CTL0 register). 

6. 

Start TIMER2 by writing ‘1’ to the CEN bit (TIMER2_CTL0 register). 

Figure 17-32. Pause mode of TIMER0 controlled by O0CPREF signal of TIMER2 

TIMER_CK

CNT_REG

TRGIF

CNT_REG

60

O0CPRE

61

62

63

00

01

11

12

13

14

TIMER2

TIMER0

 

 

Using an external trigger to start two timers synchronously. 

The start of TIMER0 is triggered by the enable signal of TIMER2, and TIMER2 is triggered by 
its CI0 input rising edge. To ensure that two timers start synchronously, TIMER2 must be 
configured in master/slave mode. Steps are shown as follows: 

1. 

Configure TIMER2 in slave mode, and select CI0_ED as the input trigger (TRGS=3’b100 
in the TIMER2_SMCFG register). 

2. 

Configure TIMER2 in event mode (SMC=3’b110 in the TIMER2_SMCFG register). 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Panasonic MICROCOMPUTER MN103S Connection Diagrams preview
MICROCOMPUTER MN103S
Brand: Panasonic Pages: 5
Panasonic MICROCOMPUTER MN103S Application Note preview
MICROCOMPUTER MN103S
Brand: Panasonic Pages: 21
Panasonic FP2 Series Manual preview
FP2 Series
Brand: Panasonic Pages: 56
Panasonic FP2 Series Product Manual preview
FP2 Series
Brand: Panasonic Pages: 28
Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Brand: Panasonic Pages: 2
Panasonic WJMPU955 - PROCESSING UNIT - TMU Operating Instructions Manual preview
WJMPU955 - PROCESSING UNIT - TMU
Brand: Panasonic Pages: 62
Barco EX Safety Manual preview
EX
Brand: Barco Pages: 100
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Brand: Cateye Pages: 15
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
STMicroelectronics ST62GP-EMU2 HDS2 Series User Manual preview
ST62GP-EMU2 HDS2 Series
Brand: STMicroelectronics Pages: 58
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
Intel CORE 2 DUO E4000 - 3-2008 Datasheet preview
CORE 2 DUO E4000 - 3-2008
Brand: Intel Pages: 122
COUGAR Vortex SPB 120 User Manual preview
Vortex SPB 120
Brand: COUGAR Pages: 2
ADTRAN 1200864L1 Quick Start Manual preview
1200864L1
Brand: ADTRAN Pages: 2
Aim ACE1553-3U-4 Hardware Manual preview
ACE1553-3U-4
Brand: Aim Pages: 35

Brands by name

Popular brands

Load more brands