GigaDevice Semiconductor GD32VF103 User Manual Download Page 413

Page: 413 / 536

GD32VF103 User Manual

413

The hardware computes the CRC value after each transmitted bit, when the TRANS

is set, a read to this register could return an intermediate value. The different frame

formats (LF bit of the SPI_CTL0) will get different CRC values.

This register is reset when the CRCEN bit in SPI_CTL0 register or the SPIxRST bit

in RCU reset register is set.

18.11.8.

I2S control register (SPI_I2SCTL)

Address offset: 0x1C

Reset value: 0x0000

This register can be accessed by half-word (16-bit) or word (32-bit).

Reserved

I2SSEL

I2SEN

I2SOPMOD[1:0]

PCMSMO

Reserved

I2SSTD[1:0]

CKPL

DTLEN[1:0]

CHLEN

Bits

Fields

Descriptions

31:12

Reserved

Must be kept at reset value.

I2SSEL

I2S mode selection

0: SPI mode

1: I2S mode

This bit should be configured when SPI/I2S is disabled.

I2SEN

I2S enable

0: I2S is disabled

1: I2S is enabled

This bit is not used in SPI mode.

9:8

I2SOPMOD[1:0]

I2S operation mode

00: Slave transmission mode

01: Slave reception mode

10: Master transmission mode

11: Master reception mode

This bit should be configured when I2S is disabled.

This bit is not used in SPI mode.

PCMSMOD

PCM frame synchronization mode

0: Short frame synchronization

1: Long frame synchronization

This bit has a meaning only when PCM standard is used.

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands