manualshive.com logo in svg

GigaDevice Semiconductor GD32VF103, User Manual

The GigaDevice Semiconductor GD32VF103 offers a powerful user manual, essential for seamless operation and troubleshooting. Easily access and download the manual for free from our website, ensuring efficient utilization of this remarkable product. Unlock the full potential of the GD32VF103 with our comprehensive and user-friendly manual.

Share
Download
background image

                                                                                                         

GD32VF103 User Manual

 

192 

 

12.3.7. 

DAC output voltage 

The analog output voltage on the DAC pin is determined by the following equation: 

DAC

output

=V

REF+

*DAC_DO/4096                                      (12-1) 

The digital input is linearly converted to an analog output voltage, its range is 0 to V

REF+

. 

12.3.8. 

DMA request 

When the external trigger is enabled, the DMA request is enabled by setting the DDMAENx 

bits  of  the  DAC_CTL  register.  A  DAC  DMA  request  will  be  generated  when  an  external 

hardware trigger (not a software trigger) occurs.   

12.3.9. 

DAC concurrent conversion 

When the two DACs work at the same time, for maximum bus bandwidth utilization in specific 

applications, two DACs can be configured in concurrent mode. In concurrent mode, two DACs 

data transfer (DACx_DH to DACx_DO) will be at the same time. 

There  are  three  concurrent  registers  that  can  be  used  to  load  the  DACx_DH  value: 

DACC_R8DH, DACC_R12DH and DACC_L12DH. You just need to access a unique register 

to realize driving both DACs at the same time. 

When external trigger is enabled, both DTENx bits should be set. DTSEL0 and DTSEL1 bits 

should be configured with the same value. 

When DMA is enabled, only one of the DDMAENx bits should be set.   

The noise mode and noise bit width can be configured either the same or different, depending 

on the usage. 

 

 

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32VF103

MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Brand: MA lighting Pages: 36
Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
Amplifier Tech ATP6700 Owner'S Manual preview
ATP6700
Brand: Amplifier Tech Pages: 36
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Brand: A2B Electronics Pages: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Brand: ZALMAN Pages: 6
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Brand: Qlogic Pages: 76
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
Xenteq SR 200-12 User Manual preview
SR 200-12
Brand: Xenteq Pages: 16
Maxtor DiamondMax 8S Specification Sheet preview
DiamondMax 8S
Brand: Maxtor Pages: 2
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
ATI Technologies Radeon Online Manual preview
Radeon
Brand: ATI Technologies Pages: 87
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12

Brands by name

Popular brands

Load more brands