manualshive.com logo in svg

GigaDevice Semiconductor GD32F403 Series, User Manual

The GigaDevice Semiconductor GD32F403 Series offers a comprehensive user manual for easy navigation and optimal usage. Available for free download at manualshive.com, this manual provides detailed instructions, troubleshooting tips, and specifications to enhance your experience with these exceptional semiconductor devices.

Share
Download
background image

                                                                                                     

GD32F403xx User Manual

 

490 

 

If the NSS pin is configured as input, the NSS pin should be pulled high in master 

mode, and this bit has no effect. 

1 

DMATEN 

Transmit buffer DMA  enable 

0: Transmit buffer DMA is disabled  

1: Transmit buffer DMA is enabled . When the TBE bit in SPI_STAT  is set, it will 

generate a DMA request at corresponding DMA channel. 

0 

DMAREN 

Receive buffer DMA  enable 

0: Receive buffer DMA is disabled  

1: Receive buffer DMA is enabled . When the RBNE bit in SPI_STAT  is set, it will 

generate a DMA request at corresponding DMA channel. 

19.5.3. 

Status register (SPI_STAT) 

Address offset: 0x08 

Reset value: 0x0002 

This register has to be accessed by word(32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

FERR 

TRANS 

RXORERR 

CONFERR 

CRCERR 

TXURERR 

I2SCH 

TBE 

RBNE 

 

rc_w0 

r 

r 

r 

rc_w0 

r 

r 

r 

r 

 

Bits 

Fields 

Descriptions 

31:9 

Reserved 

Must be kept at reset value. 

8 

FERR 

Format error bit 

SPI TI Mode: 

0: No TI Mode format error 

1: TI Mode format error occurs. 

I2S Mode: 

0: No I2S format error 

1: I2S format error occurs. 

This bit is set by hardware and is able to be cleared by writing 0.   

7 

TRANS 

Transmitting on-going bit 

0: SPI or I2S is idle. 

1: SPI or I2S is currently transmitting and/or receiving a frame 

This bit is set and cleared by hardware.   

6 

RXORERR 

Reception overrun error bit 

0: No reception overrun error occurs. 

Summary of Contents for GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F403 Series

TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Brand: TCS Basys Controls Pages: 2
J+J J4C Series Installation Instructions preview
J4C Series
Brand: J+J Pages: 2
HW Group HWg-SH3 Manual preview
HWg-SH3
Brand: HW Group Pages: 18
KIPI ecoMAX360P1-C Installation And Operating Manual preview
ecoMAX360P1-C
Brand: KIPI Pages: 44
Sullair 02250160-842 Instruction Manual preview
02250160-842
Brand: Sullair Pages: 31
NXP Semiconductors AN10815 Application Note preview
AN10815
Brand: NXP Semiconductors Pages: 20
Swagelok KPF Series Maintenance Instructions Manual preview
KPF Series
Brand: Swagelok Pages: 6
LAMBERTI ELEKTRONIK Latherm HZR Comfort Operating Manual preview
Latherm HZR Comfort
Brand: LAMBERTI ELEKTRONIK Pages: 16
3M Touch Screen Controller SX112 Reference Manual preview
Touch Screen Controller SX112
Brand: 3M Pages: 33
HomeMatic HM-Sec-SFA-SM Installation And Operating Manual preview
HM-Sec-SFA-SM
Brand: HomeMatic Pages: 38
VAL VLC-2430-4 Operation Manual preview
VLC-2430-4
Brand: VAL Pages: 10
Zonet ZUC2401 Quick Installation Manual preview
ZUC2401
Brand: Zonet Pages: 2
Bartels Mikrotechnik mpSmart-Dosing Instruction Manual preview
mpSmart-Dosing
Brand: Bartels Mikrotechnik Pages: 9
Solcon RVS-DXM Instruction Manual preview
RVS-DXM
Brand: Solcon Pages: 65
dunkermotoren ServoTube 25 Instruction Manual preview
ServoTube 25
Brand: dunkermotoren Pages: 34
Toho Electronics TTM-00BW Operation Manual preview
TTM-00BW
Brand: Toho Electronics Pages: 37
Matelec FPC-30020-CON Owner'S Operation Manual preview
FPC-30020-CON
Brand: Matelec Pages: 12
Sinclair XK64 User Manual preview
XK64
Brand: Sinclair Pages: 28

Brands by name

Popular brands

Load more brands