manualshive.com logo in svg

GigaDevice Semiconductor GD32F403 Series, User Manual

The GigaDevice Semiconductor GD32F403 Series offers a comprehensive user manual for easy navigation and optimal usage. Available for free download at manualshive.com, this manual provides detailed instructions, troubleshooting tips, and specifications to enhance your experience with these exceptional semiconductor devices.

Share
Download
background image

                                                                                                     

GD32F403xx User Manual

 

309 

 

16.2.4. 

Function overview 

Clock source configuration 

The general level0 TIMER has the capability of being clocked by either the CK_TIMER or an 
alternate clock source controlled by SMC (TIMERx_SMCFG bit [2:0]). 

◼

 

SMC [2:0] == 3’b000. Internal timer clock CK_TIMER which is from module RCU.  

The default internal clock source is the CK_TIMER used to drive the counter prescaler when 
the SMC [2:0] == 3’b000. When the CEN is set, the CK_TIMER will be divided by PSC value 
to generate PSC_CLK. 

In this mode, the TIMER_CK, driven counter’s prescaler to count, is equal to CK_TIMER 
which is from RCU. 

If the SMC [2:0] in the TIMERx_SMCFG register are setting to an available value including 
0x1, 0x2, 0x3 and 0x7, the prescaler is clocked by other clock sources selected by the TRGS 
[2:0] in the TIMERx_SMCFG register and described as follows. When the SMC [2:0] bits are 
set to 0x4, 0x5 or 0x6, the internal clock CK_TIMER is the counter prescaler driving clock 
source.  

Figure 16-30. Timing chart of internal clock divided by 1 

 

 

CK_TIMER

CEN

PSC_CLK = TIMER_CK

CNT_REG

Reload Pulse

17

18

19

20

21

22

update event 

generate(UPG)

23

00

01

02

03

04

05

06

07

Update event (UPE)

 

◼

 

SMC [2:0] == 3’b111(external clock mode 0). External input pin source 

The TIMER_CK, which drives counter’s prescaler to count, can be triggered by the event of 
rising or  falling edge  on  the external pin  TIMERx_CI0/TIMERx_CI1. This mode  can  be 
selected by setting SMC [2:0] to 0x7 and the TRGS [2:0] to 0x4, 0x5 or 0x6.  

And, the counter prescaler can also be driven by rising edge on the internal trigger input pin 
ITI0/1/2/3. This mode can be selected by setting SMC [2:0] to 0x7 and the TRGS [2:0] to 0x0, 
0x1, 0x2 or 0x3. 

Summary of Contents for GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F403 Series

FAAC 740 D User Manual preview
740 D
Brand: FAAC Pages: 64
Lawler 801 Installation & Maintenance Manual preview
801
Brand: Lawler Pages: 4
QTP 10900 Quick Start Manual preview
10900
Brand: QTP Pages: 2
Interlogix TruPortal TP-ADD-1DIP Quick Reference preview
TruPortal TP-ADD-1DIP
Brand: Interlogix Pages: 9
YASKAWA J1000 CIMR-JC series Option Manual preview
J1000 CIMR-JC series
Brand: YASKAWA Pages: 26
SDC E4KP ENTRYCHECK Operating Instructions Manual preview
E4KP ENTRYCHECK
Brand: SDC Pages: 6
McIntosh MHT200 Owner'S Manual preview
MHT200
Brand: McIntosh Pages: 68
Fairford Synergy SGY-101 Quick Start Manual preview
Synergy SGY-101
Brand: Fairford Pages: 20
ST UM1932 User Manual preview
UM1932
Brand: ST Pages: 40
Varian 969-9507 Instruction Manual preview
969-9507
Brand: Varian Pages: 37
Zonex DIGI3U Installation Manual preview
DIGI3U
Brand: Zonex Pages: 16
Samson TROVIS 5579 Mounting And Operating Instructions preview
TROVIS 5579
Brand: Samson Pages: 182
Invacare MK5 NX w/ACC Service Manual preview
MK5 NX w/ACC
Brand: Invacare Pages: 44
M-system EAR70 Instruction Manual preview
EAR70
Brand: M-system Pages: 8
S&S Northern Merlin 500S User Manual preview
Merlin 500S
Brand: S&S Northern Pages: 8
Linx Technologies HumPRO Series Quickstart Reference preview
HumPRO Series
Brand: Linx Technologies Pages: 2
Gardner Denver Governor TEN014980 User Manual preview
Governor TEN014980
Brand: Gardner Denver Pages: 194
Fisher 67D Series Instruction Manual preview
67D Series
Brand: Fisher Pages: 12

Brands by name

Popular brands

Load more brands