manualshive.com logo in svg

GigaDevice Semiconductor GD32F403 Series, User Manual, Page: 305 / 711

Share
Download
GigaDevice Semiconductor GD32F403 Series User Manual Download Page 305

                                                                                                     

GD32F403xx User Manual

 

305 

 

This filed defines the number(n) of the register that DMA will access(R/W), n = 

(DMATC [4:0] +1). DMATC [4:0] is from 

5’b0_0000  to 5’b1_0001. 

7:5 

Reserved 

Must be kept at reset value. 

4:0 

DMATA  [4:0] 

DMA transfer access start address 

This filed define the first address for the DMA access the TIMERx_DMATB.  When 

access is done through the TIMERx_DMA address first time, this bit-field specifies 

the address you just access. And then the second access to the TIMERx_DMATB, 

you will access the address of start a 0x4.   

DMA transfer buffer register (TIMERx_DMATB) 

Address offset: 0x4C 

Reset value: 0x0000 

This register can be accessed by half-word (16-bit) or word (32-bit) 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

DMATB[15:0] 

rw 

 

Bits   

Fields 

Descriptions 

15:0 

DMATB[15:0] 

DMA transfer buffer 

When a read or write operation is assigned to this register, the register located at 

the address range (Start Addr + Transfer Timer* 4) will be accessed. 

The transfer Timer is calculated by hardware, and ranges from 0 to DMATC. 

Configuration register (TIMERx_CFG) 

Address offset: 0xFC 

Reset value: 0x0000 

This register can be accessed by half-word (16-bit) or word (32-bit) 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

CHVSEL  OUTSEL 

 

rw 

rw 

 

Bits 

Fields 

Descriptions 

15:2 

Reserved 

Must be kept at reset value. 

1 

CHVSEL 

Write CHxVAL  register selection  

This bit-field set and reset by software. 

1: If write the CHxVAL register, the write value is same as the CHxVAL value, the 

write access ignored  

Summary of Contents for GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments