manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Introducing the GigaDevice Semiconductor GD32F20 Series - a cutting-edge product with exceptional features. Unlock the full potential of your device by accessing the comprehensive User Manual, available for free download at manualshive.com. This manual is your ultimate guide to harnessing the power of GD32F20, ensuring optimal performance and user satisfaction.

Share
Download
background image

 

                                                                                                             

GD32F20x User Manual

 

870 

 

2 

OSF 

Operate on second frame bit 

0: The TxDMA controller process the second transmit frame after the status of the 

first frame is written back to descriptor 

1:  The  TxDMA  controller process  the  second  transmit  frame  after  pushed all  first 

frame  data  into  TxFIFO  but  before  the  status  of  the  first  frame  is  written  back  to 

descriptor 

1 

SRE 

Start/stop receive enable bit 

0:  The  RxDMA  controller  will  enter  stop  state  after  transfer  complete  if  current 

received frame is transmitting to memory by RxDMA. After transfer complete, the 

next  descriptor  address  in  the  receive  table  will  become  the  current  descriptor 

address  when  restart  the  RxDMA  controller.  Only  RxDMA  controller  is  in  running 

state or suspend state, this bit can be reset by application. 

1: The RxDMA controller will enter running state. RxDMA controller fetches receive 

descriptor from receive descriptor table for receiving frames. The descriptor address 

can  either  from  current  address  in  the  ENET_DMA_RDTADDR  register  or  the 

address  after  previous  frame  stopped  by  application.  If  the  DAV  bit  in  fetched 

descriptor is reset, RxDMA controller will enter suspend state and RBU bit will be 

set.  This  bit  can  be  set  only  when  RxDMA  controller  is  in  stop  state  or  suspend 

state.  This  bit  should  be  set  after  all  other  DMA  registers  have  been  configured, 

otherwise the action of RxDMA is unpredictable. 

0 

Reserved 

Must be kept at reset value 

27.4.49. 

DMA interrupt enable register (ENET_DMA_INTEN) 

Address offset: 0x101C 

Reset value: 0x0000 0000 

This register configures the interrupts which are reflected in ENET_DMA_STAT register. 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

NIE 

 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

AIE 

ERIE 

FBEIE 

Reserved 

ETIE 

RWTIE 

RPSIE 

RBUIE 

RIE 

TUIE 

ROIE 

TJTIE 

TBUIE 

TPSIE 

TIE 

rw 

rw 

rw 

 

rw 

rw 

rw 

rw 

rw 

rw 

rw 

rw 

rw 

rw 

rw 

 

Bits 

Fields 

Descriptions 

31:17 

Reserved 

Must be kept at reset value 

16 

NIE 

Normal interrupt summary enable bit 

0: A normal interrupt is disabled.   

1: A normal interrupt is enabled 

This bit enables the following bits: 

TS (ENET_DMA_STAT [0]): Transmit interrupt 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F20 Series

ABB ACS355 series Quick Start Up Manual preview
ACS355 series
Brand: ABB Pages: 139
ABB ACH400 Series Retrofit Manual preview
ACH400 Series
Brand: ABB Pages: 28
ABB TZIDC-110 Operating Instructions Manual preview
TZIDC-110
Brand: ABB Pages: 59
TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Brand: TCS Basys Controls Pages: 2
Jands 4PAK Operating Manual preview
4PAK
Brand: Jands Pages: 6
Rain Bird ESP-LXD Installation, Programming & Operation Manual preview
ESP-LXD
Brand: Rain Bird Pages: 138
J+J J4C S20 Quick Start Manual preview
J4C S20
Brand: J+J Pages: 4
IBM MTM 2145-SV1 Hardware Installation Manual preview
MTM 2145-SV1
Brand: IBM Pages: 214
Zero 88 Chilli Master Operating Manual preview
Chilli Master
Brand: Zero 88 Pages: 34
Kramer FC-21ETH User Manual preview
FC-21ETH
Brand: Kramer Pages: 60
Maverick EP7312 User Manual preview
EP7312
Brand: Maverick Pages: 122
NXP Semiconductors LPC2880 User Manual preview
LPC2880
Brand: NXP Semiconductors Pages: 362
On-Q lyriQ AU7394 Series Instruction/Installation Sheet preview
lyriQ AU7394 Series
Brand: On-Q Pages: 8
Samson Graphite MF8 Quick Start Manual preview
Graphite MF8
Brand: Samson Pages: 64
SystemAir NOTUS-R Installation, Maintenance And Operation Instructions preview
NOTUS-R
Brand: SystemAir Pages: 4
National Instruments NI cRIO-9025 User Manual And Specifications preview
NI cRIO-9025
Brand: National Instruments Pages: 20
Eliweli EW-601 Instructions For Use preview
EW-601
Brand: Eliweli Pages: 2
Bürkert Type 8605 Quick Start preview
Type 8605
Brand: Bürkert Pages: 5

Brands by name

Popular brands

Load more brands