manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Introducing the GigaDevice Semiconductor GD32F20 Series - a cutting-edge product with exceptional features. Unlock the full potential of your device by accessing the comprehensive User Manual, available for free download at manualshive.com. This manual is your ultimate guide to harnessing the power of GD32F20, ensuring optimal performance and user satisfaction.

Share
Download
background image

 

                                                                                                             

GD32F20x User Manual

 

844 

 

5 

MSCR 

MSC receive status bit 

0: All the bits in register ENET_MSC_RINTF are cleared 

1: An interrupt is generated in the ENET_MSC_RINTF register 

4 

MSC 

MSC status bit 

This bit is logic ORed from MSCT and MSCR bit. 

0: Both MSCT and MSCR bits in this register are low 

1: Any of bit 6 (MSCT) or bit 5 (MSCR) is set high 

3 

WUM 

WUM status bit 

This bit is logic ORed from WUFR and MPKR bit in ENET_MAC_WUM register. 

0: Wakeup frame or Magic Packet frame is not received 

1: A Magic packet or remote wakeup frame is received in power down Mode 

2:0 

Reserved 

Must be kept at reset value 

27.4.13. 

MAC interrupt mask register (ENET_MAC_INTMSK) 

Address offset: 0x003C 

Reset value: 0x0000 0000 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

TMSTIM 

Reserved 

WUMIM 

Reserved 

 

rw 

 

rw 

 

 

Bits 

Fields 

Descriptions 

31:10 

Reserved 

Must be kept at reset value 

9 

TMSTIM 

Timestamp trigger interrupt mask bit 

0:Unmask the timestamp interrupt generation 

1:Mask the timestamp interrupt generation 

8:4 

Reserved 

Must be kept at reset value 

3 

WUMIM 

WUM interrupt mask bit 

0:  Unmask  the  interrupt  generation  due  to  the  WUM  bit  in  ENET_MAC_INTF 

register 

1: Mask the interrupt generation due to the WUM bit in ENET_MAC_INTF register 

2:0 

Reserved 

Must be kept at reset value 

27.4.14. 

MAC address 0 high register (ENET_MAC_ADDR0H) 

Address offset: 0x0040 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F20 Series

ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Brand: ABB Pages: 4
UniKey SR3 Installation Manual & User Manual preview
SR3
Brand: UniKey Pages: 20
OEG KMS Manual preview
KMS
Brand: OEG Pages: 168
HANYOUNG NUX NP100 Manual preview
NP100
Brand: HANYOUNG NUX Pages: 36
HANYOUNG NUX HY Series Instruction Manual preview
HY Series
Brand: HANYOUNG NUX Pages: 4
MADRIX Nebula User Manual preview
Nebula
Brand: MADRIX Pages: 91
MADRIX Nebula Quick Start Manual preview
Nebula
Brand: MADRIX Pages: 40
YASKAWA MP Series Driver Manual preview
MP Series
Brand: YASKAWA Pages: 18
IDTECK Star RFL200 Quick Manual preview
Star RFL200
Brand: IDTECK Pages: 12
Banner XS26-2 Series Manual preview
XS26-2 Series
Brand: Banner Pages: 2
Eaton CGLine+ Web Controller Installation And Operating Instructions Manual preview
CGLine+ Web Controller
Brand: Eaton Pages: 28
ZKTeco IN710 Quick Start Manual preview
IN710
Brand: ZKTeco Pages: 11
iluminize 5110 V1 Manual preview
5110 V1
Brand: iluminize Pages: 2
HW Group HWg-SH3 Manual preview
HWg-SH3
Brand: HW Group Pages: 18
CORNING Ascent 6970 Instruction Manual preview
Ascent 6970
Brand: CORNING Pages: 142
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Brand: Procom Pages: 10
Swagelok TBVS4 User Manual preview
TBVS4
Brand: Swagelok Pages: 16
Zencontrol zc-controller Instructions preview
zc-controller
Brand: Zencontrol Pages: 2

Brands by name

Popular brands

Load more brands