manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Introducing the GigaDevice Semiconductor GD32F20 Series - a cutting-edge product with exceptional features. Unlock the full potential of your device by accessing the comprehensive User Manual, available for free download at manualshive.com. This manual is your ultimate guide to harnessing the power of GD32F20, ensuring optimal performance and user satisfaction.

Share
Download
background image

 

                                                                                                             

GD32F20x User Manual

 

50 

 

Figure 2-3. Process of word program operation 

Set  the PG bit 

Is the LK bit is 0

Perform word/half 

word write by DBUS

Start

Yes

No

Unlock the 

FMC_CTL

Is the BUSY bit is 0

Yes

No

Is the BUSY bit is 0

Yes

No

Finish

 

For the GD32F20x_CL with flash more than 512KB, the program procedure applied to bank1 

is similar to the procedure applied to bank0.

 

Note:

 Reading the flash should be avoided when a program/erase operation is ongoing in the 

same bank. And flash memory accesses failed if the CPU enters the power saving modes. 

2.3.7. 

Option bytes Erase 

The FMC provides an erase function which is used to initialize the option bytes block in flash. 

The following steps show the erase sequence.   

 

Unlock the FMC_CTL0 register if necessary. 

 

Check the BUSY bit in FMC_STAT0 register to confirm that no Flash memory operation 

is in progress (BUSY equal to 0). Otherwise, wait until the operation has finished. 

 

Unlock the option bytes operation bits in FMC_CTL0 register if necessary. 

 

Wait until OBWEN bit is set in FMC_CTL0 register. 

 

Set OBER bit in FMC_CTL0 register.   

 

Send  the  option  bytes  erase  command  to  the  FMC  by  setting  the  START  bit  in 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F20 Series

Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Brand: Galcon Pages: 32
Jands SafeGuard Installation Manual preview
SafeGuard
Brand: Jands Pages: 7
hager coviva Smartbox TKP100A Operation And Configuration Instructions preview
coviva Smartbox TKP100A
Brand: hager Pages: 34
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Brand: HEIDENHAIN Pages: 257
Industrial Shields M-DUINO PLUS series User Manual preview
M-DUINO PLUS series
Brand: Industrial Shields Pages: 46
MacroAir Technologies Controller 30 Operation Manual preview
Controller 30
Brand: MacroAir Technologies Pages: 32
A10 Networks Harmony 2000 Quick Start Manual preview
Harmony 2000
Brand: A10 Networks Pages: 2
Oriental motor ASD10A-K Operating Manual preview
ASD10A-K
Brand: Oriental motor Pages: 52
Opt OPT-DPA1024E-4 Manual preview
OPT-DPA1024E-4
Brand: Opt Pages: 40
MAASLAND FLEXESS DUO Manual preview
FLEXESS DUO
Brand: MAASLAND Pages: 10
Seitron RD ADA1 Quick Start Manual preview
RD ADA1
Brand: Seitron Pages: 2
Samson 4708-1152 Mounting And Operating Instructions preview
4708-1152
Brand: Samson Pages: 32
X10 SC503 Owner'S Manual preview
SC503
Brand: X10 Pages: 3
Wahlberg 255.700 User Manual preview
255.700
Brand: Wahlberg Pages: 40
E-T-A ControlPlex CPC12 T Series User Manual preview
ControlPlex CPC12 T Series
Brand: E-T-A Pages: 30
InPlay IN1BN-DKC0-100-C0 User Manual preview
IN1BN-DKC0-100-C0
Brand: InPlay Pages: 11
Ledj STAR11 User Manual preview
STAR11
Brand: Ledj Pages: 12
C-LOGIC 502-PC Instruction Manual preview
502-PC
Brand: C-LOGIC Pages: 2

Brands by name

Popular brands

Load more brands