GigaDevice Semiconductor GD32F20 Series User Manual Download Page 257

Page: 257 / 950

GD32F20x User Manual

257

Figure 14-2. Single conversion mode

CH2

EOC

Regular

trigger

Sample

Convert

After conversion of a single regular channel, the conversion data will be stored in the

ADC_RDATA register, the EOC will be set. An interrupt will be generated if the EOCIE bit is

set.

After conversion of a single inserted channel, the conversion data will be stored in the

ADC_IDATA0 register, the EOC and EOIC will be set. An interrupt will be generated if the

EOCIE or EOICIE bit is set.

Software procedure for a single conversion of a regular channel:

Make sure the DISRC, SM in the ADC_CTL0 register and CTN bit in the ADC_CTL1

Configure RSQ0 with the analog channel number

Configure ADC_SAMPTx register

Configure ETERC and ETSRC bits in the ADC_CTL1 register if in need

Set the SWRCST bit, or generate an external trigger for the regular group

Wait the EOC flag to be set

Read the converted in the ADC_RDATA register

Clear the EOC flag by writing 0 to it

Software procedure for a single conversion of an inserted channel:

Make sure the DISIC, SM in the ADC_CTL0 register are reset

Configure ISQ3 with the analog channel number

Configure ADC_SAMPTx register

Configure ETEIC and ETSIC bits in the ADC_CTL1 register if in need

Set the SWICST bit, or generate an external trigger for the inserted group

Wait the EOC/EOIC flags to be set

Read the converted in the ADC_IDATA0 register

Clear the EOC/EOIC flags by writing 0 to them

Continuous conversion mode

This mode can be run on the regular channel group. The continuous conversion mode will be

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32F20 Series

Reviews:

Related manuals for GD32F20 Series

Brands by name

Popular brands

GigaDevice Semiconductor GD32F20 Series, User Manual

Search results

Summary of Contents for GD32F20 Series

Reviews:

Related manuals for GD32F20 Series

Brands by name

Popular brands