manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

787

 

 

OUT transfers operation sequence 

1. 

Initialize USBFS global registers. 

2. 

Initialize the endpoint and enable the endpoint. 

3. 

When an OUT token is received, USBFS receives the data packet or response with an 
NAK  handshake  based  on  the  status  of  Rx  FIFO  and  register  configuration.  If  the 
transaction is finished successfully (USBFS receives and saves the data packet into Rx 
FIFO  successfully  and  sends  ACK  handshake  on  USB  bus),  PCNT  in 
USBFS_DOEPxLEN register is decreased by 1 and the ACK flag is triggered, otherwise, 
the status flags report the transaction result. 

4. 

After all the data packets in a transfer are successfully received on USB  bus, USBFS 
pushes  a TF  status  entry  into  the  Rx  FIFO  on  top  of  the  last  packet  data.  Thus  after 
reading  and  poping  all  the  received  data  packet,  the TF  status  entry  is  read,  USBFS 
generates  TF  flag  to  indicate  that  the  transfer  successfully  is  finished  and  the  OUT 
endpoint is disabled. 

24.6. 

Interrupts 

USBFS has two interrupts: global interrupt and wake-up interrupt. 

The source flags of the global interrupt are readable in USBFS_GINTF register and are listed 
in 

Table 24-2. USBFS global interrupt

. 

Table 24-2. USBFS global interrupt 

Interrupt Flag 

Description 

Operation Mode 

SESIF 

Session interrupt

 

Host or device mode

 

DISCIF 

Disconnect interrupt flag

 

Host Mode

 

IDPSC 

ID pin status change

 

Host or device mode

 

PTXFEIF 

Periodic Tx FIFO empty interrupt flag

 

Host Mode

 

HCIF 

Host channels interrupt flag

 

Host Mode

 

HPIF 

Host port interrupt flag

 

Host Mode

 

ISOONCIF/PXN

CIF 

Periodic transfer Not Complete 

Interrupt flag /Isochronous OUT 

transfer Not Complete Interrupt Flag

 

Host or device mode 

ISOINCIF 

Isochronous IN transfer Not Complete 

Interrupt Flag

 

Device mode

 

OEPIF 

OUT endpoint interrupt flag

 

Device mode

 

IEPIF

 

IN endpoint interrupt flag

 

Device mode

 

EOPFIF

 

End of periodic frame interrupt flag

 

Device mode

 

ISOOPDIF

 

Isochronous OUT packet dropped 

interrupt flag

 

Device mode

 

ENUMF

 

Enumeration finished

 

Device mode

 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
OMC W150 Installation And Maintenance Instruction preview
W150
Brand: OMC Pages: 18
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Brand: Samson Pages: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Brand: Samson Pages: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Brand: Samson Pages: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Brand: Samson Pages: 68
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Brand: Samson Pages: 80
Haehne DCX Quick Start Manual preview
DCX
Brand: Haehne Pages: 44
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
YASKAWA FSDrive-MV1000 Series Instructions For Use Manual preview
FSDrive-MV1000 Series
Brand: YASKAWA Pages: 260
YASKAWA iQpump1000 Installation & Start?Up Manual preview
iQpump1000
Brand: YASKAWA Pages: 114
YASKAWA MOTOMAN FS100 Operator'S Manual preview
MOTOMAN FS100
Brand: YASKAWA Pages: 20
YASKAWA yasnac lx3 Maintenance Manual preview
yasnac lx3
Brand: YASKAWA Pages: 152
YASKAWA MOTOMAN FS100 Option Addendum preview
MOTOMAN FS100
Brand: YASKAWA Pages: 20
YASKAWA MOTOMAN FS100 Instructions Manual preview
MOTOMAN FS100
Brand: YASKAWA Pages: 17
YASKAWA 1000-Series Technical Manual preview
1000-Series
Brand: YASKAWA Pages: 58
YASKAWA J1000 CIMR-JC series Cheat Sheet preview
J1000 CIMR-JC series
Brand: YASKAWA Pages: 2
YASKAWA SI-EP3 Technical Manual preview
SI-EP3
Brand: YASKAWA Pages: 58

Brands by name

Popular brands

Load more brands