manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

673

 

 

Unicast frame source address filter 

Enable MAC address 1 to MAC address 3 register and set the corresponding SAF bit in the 

MAC address high register, the MAC compares and filter the source address (SA) field in the 

received frame with the values programmed in the SA registers. MAC also supports the group 

filter on the source address. If the SAFLT bit in frame filter register ENET_MAC_FRMF is set, 

MAC drops the frame that failed the source address filtering; meanwhile the filter result will 

reflect  by  SAFF  bit  in  RDES0  of  DMA  receive  descriptor.  When  the  SAFLT  bit  is  set,  the 

destination address filter is also at work, so the result of the filter is simultaneous determined 

by DA and SA filter. This means that, as long as a frame does not pass any one of the filters 

(DA  filter  or  SA  filter),  it  will  be  discarded.  Only  a  frame  passing  the  entire  filter  can  be 

forwarded to the application. 

Reverse filtering operation 

MAC can reverse filter-match result at the final output whether the destination address filtering 

or  source  address  filtering.  By  setting  the  DAIFLT  and  SAIFLT  bits  in  ENET_MAC_FRMF 

register, this address filter reverse function can be  enabled. DAIFLT bit is used for unicast 
and multicast frames’ DA filtering result, SAIFLT bit is used for unicast and multicast frames 

SA filtering result. 

The  following  two  tables  summarize  the  destination  address  and  source  address  filters 

working condition at different configuration. 

Table 22-4. Destination address filtering table 

Frame 

Type 

PM  HPFLT  HUF  DAIFLT  HMF  MFD  BFRMD 

DA filter operation 

Broadcast 

1 

- 

- 

- 

- 

- 

- 

Pass 

0 

- 

- 

- 

- 

- 

0 

Pass 

0 

- 

- 

- 

- 

- 

1 

Fail 

Unicast 

1 

- 

- 

- 

- 

- 

- 

Pass all frames 

0 

- 

0 

0 

- 

- 

- 

Pass on perfect/group filter match 

0 

- 

0 

1 

- 

- 

- 

Fail on perfect/group filter match 

0 

0 

1 

0 

- 

- 

- 

Pass on hash filter match 

0 

0 

1 

1 

- 

- 

- 

Fail on hash filter match 

0 

1 

1 

0 

- 

- 

- 

Pass on hash or perfect/group filter 

match 

0 

1 

1 

1 

- 

- 

- 

Fail on hash or perfect/group filter 

match 

Multicast 

1 

- 

- 

- 

- 

- 

- 

Pass all frames 

- 

- 

- 

- 

- 

1 

- 

Pass all frames 

0 

- 

- 

0 

0 

0 

- 

Pass on perfect/group filter match and 

drop PAUSE control frames if PCFRM = 

0x 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

wattio AIR Read Me preview
AIR
Brand: wattio Pages: 20
Waterway OASIS Instruction Manual preview
OASIS
Brand: Waterway Pages: 16
Data Aire dap4 touch Protocol Manual preview
dap4 touch
Brand: Data Aire Pages: 13
Uclear Motion Series User Manual preview
Motion Series
Brand: Uclear Pages: 40
Samson 3371 Series Mounting And Operating Instructions preview
3371 Series
Brand: Samson Pages: 70
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
ICS Tunnel Master Jr User Manual preview
Tunnel Master Jr
Brand: ICS Pages: 70
LEGRAND Arteor 5 742 74 Quick Start Manual preview
Arteor 5 742 74
Brand: LEGRAND Pages: 2
SAMES KREMLIN LP 6 - 0.5/4 Translation From The Original Manual preview
LP 6 - 0.5/4
Brand: SAMES KREMLIN Pages: 5
NEC V850E/RS1 User Manual preview
V850E/RS1
Brand: NEC Pages: 852
Warner Electric CBC-150 Series Installation And Operation Manual preview
CBC-150 Series
Brand: Warner Electric Pages: 4
Flycolor Raptor S-Tower F4-20A User Manual preview
Raptor S-Tower F4-20A
Brand: Flycolor Pages: 2
ITRON RB 4000 Instruction Manual preview
RB 4000
Brand: ITRON Pages: 24
Azbil AUR450C User Manual preview
AUR450C
Brand: Azbil Pages: 62
ROLA-CHEM 554200 Operating Manual preview
554200
Brand: ROLA-CHEM Pages: 16
Magnetek GPD 333 Technical Manual preview
GPD 333
Brand: Magnetek Pages: 81
Wachendorff URDR001A User Manual preview
URDR001A
Brand: Wachendorff Pages: 60
Zero 88 Sirius 24 Installation And Operation Instructions preview
Sirius 24
Brand: Zero 88 Pages: 5

Brands by name

Popular brands

Load more brands