manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

41

 

 

Selected boot source 

Boot mode selection pins 

Boot1 

Boot0 

Boot loader 

0 

1 

On-chip SRAM 

1 

1 

Note:

 When the boot source is hoped to be set as 

“Main Flash Memory”, the Boot0 pin has 

to be connected with GND definitely and can not be floating. 

After power-on sequence or a system reset, the Arm

®

 Cortex

®

-M3 processor fetches the top-

of-stack value from address 0x0000 0000 and the base address of boot code from 0x0000 

0004 in sequence. Then, it starts executing code from the base address of boot code. 

Due  to  the  selected  boot  source,  either  the  main  flash  memory  (original  memory  space 

beginning  at  0x0800  0000)  or  the  system  memory  (MD  series  original  memory  space 

beginning at 0x1FFF FF00, please refer to 

Table 2-2. GD32F10x_CL and GD32F10x_HD, 

GD32F10x_XD

 for other series addresses) is aliased in the boot memory space which begins 

at the address 0x0000 0000. When the on-chip SRAM whose memory space is beginning at 

0x2000 0000 is selected as the boot source, in the application initialization code, you have to 

relocate the vector table in SRAM using the NVIC exception table and offset register. 

The embedded boot loader is located in the System memory, which is used to reprogram the 

Flash memory. In GD32F10x devices, the boot loader can be activated through the USART0 

interface.   

1.5. 

Device electronic signature 

The  device  electronic  signature  contains  memory  size  information  and  the  96-bit  unique 

device ID. It is stored in the information block of the Flash memory. The 96-bit unique device 

ID is unique for any device. It can be used as serial numbers, or part of security keys, etc.   

 

 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Microchip Technology PLECS Quick Start Manual preview
PLECS
Brand: Microchip Technology Pages: 37
Nemesis OSCA-I8 User Manual preview
OSCA-I8
Brand: Nemesis Pages: 6
YASKAWA CIMR-ZU Series Programming Manual preview
CIMR-ZU Series
Brand: YASKAWA Pages: 340
Ultraflex B 301 Installation And Maintenance Manual preview
B 301
Brand: Ultraflex Pages: 48
SainSmart 101-40-173 Assembly preview
101-40-173
Brand: SainSmart Pages: 17
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Brand: KEPCO Pages: 34
Savant SmartControl RS232 Quick Reference Manual preview
SmartControl RS232
Brand: Savant Pages: 2
AUMA PROFOX PF-M100X Manual preview
PROFOX PF-M100X
Brand: AUMA Pages: 56
SUNWIND DR2210N -DDB User Manual preview
DR2210N -DDB
Brand: SUNWIND Pages: 53
HobbyKing NanoWii Manual preview
NanoWii
Brand: HobbyKing Pages: 16
Yaesu G-800DXA User Manual preview
G-800DXA
Brand: Yaesu Pages: 20
YASKAWA FS100L Instructions Manual preview
FS100L
Brand: YASKAWA Pages: 28
UNIT ELECTRONICS DualMCU Product Reference Manual preview
DualMCU
Brand: UNIT ELECTRONICS Pages: 40
X10 Sundowner SD533 Owner'S Manual preview
Sundowner SD533
Brand: X10 Pages: 3
Infineon XC800 AP08113 Application Note preview
XC800 AP08113
Brand: Infineon Pages: 22
Samwontech TEMP2020 series Operation Manual preview
TEMP2020 series
Brand: Samwontech Pages: 75
Vega VEGATOR 121 Operating Instructions Manual preview
VEGATOR 121
Brand: Vega Pages: 32
Offgridtec MPPT PRO-X Series User Manual preview
MPPT PRO-X Series
Brand: Offgridtec Pages: 40

Brands by name

Popular brands

Load more brands