manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

220

 

 

11.5. 

ADC sync mode 

In devices with more than one ADC, the ADC sync mode can be used. In ADC sync mode, 

the conversion starts alternately or simultaneously triggered by ADC0 to ADC1, according to 

the sync mode configurated by the SYNCM[3:0] bits in ADC1_CTL0 register. 

In sync  mode,  when  configure  the  conversion  which  is  triggered  by  an  external  event,  the 

ADC1 must be configured as triggered by the software. However, the external trigger must 

be enabled for ADC0 and ADC1. 

The following modes can be configured in 

Table 11-5. ADC sync mode table

. 

Table 11-5. ADC sync mode table 

SYNCM[2: 0] 

mode 

0000 

Free mode 

0110 

Routine parallel mode 

0111 

Routine follow-up fast mode 

1000 

Routine follow-up slow mode 

In ADC sync mode, the DMA bit must be set even if it is not used; the converted data of ADC1 

routine

 

channel can be read from the ADC0 data register. 

Figure 11-8. ADC sync block diagram 

ADC_IN0

ADC_IN1

· ·

 

·

ADC_IN15

GPIO

V

SENSE

V

REFINT

EXTI11

A
P
B

 

B
U
S

ADC0

 (master)

ADC1

 (slave)

Routine data registers

（

16 bits

）

Routine 

channels

Routine data registers

（

16 bits

）

Routine 

channels

Routine 

trigger mux

Syncl mode 

control

 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

RadioMaster POCKET Quick Start Manual preview
POCKET
Brand: RadioMaster Pages: 10
Saftronics CV10 Quick Start Manual preview
CV10
Brand: Saftronics Pages: 13
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Brand: Samwontech Pages: 91
Samson TROVIS 3730-1 Installation Instructions Manual preview
TROVIS 3730-1
Brand: Samson Pages: 6
Zencontrol zc-controller Instructions preview
zc-controller
Brand: Zencontrol Pages: 2
Daikin KBRCS01A Quick Start Manual preview
KBRCS01A
Brand: Daikin Pages: 2
Advantech PCI-1760U Startup Manual preview
PCI-1760U
Brand: Advantech Pages: 3
Xylem Aquavar IPC Quick Start Manual preview
Aquavar IPC
Brand: Xylem Pages: 28
Overland Storage NEO 2000e Remove & Replace Instructions preview
NEO 2000e
Brand: Overland Storage Pages: 4
Cruisair TWLC User Manual preview
TWLC
Brand: Cruisair Pages: 30
Savant SmartControl RS232 Quick Reference Manual preview
SmartControl RS232
Brand: Savant Pages: 2
Bardac PLX Product Manual preview
PLX
Brand: Bardac Pages: 235
Inner Range CONCEPT IQ User Manual preview
CONCEPT IQ
Brand: Inner Range Pages: 28
Base Line BaseStation 1000 Quick Start Manual preview
BaseStation 1000
Brand: Base Line Pages: 11
Barth Mini-PLC STG-115 Manual preview
Mini-PLC STG-115
Brand: Barth Pages: 8
9g Products INPRINT-MICRO Instruction Manual preview
INPRINT-MICRO
Brand: 9g Products Pages: 12
AKO Electronica AKO-14532 Manual preview
AKO-14532
Brand: AKO Electronica Pages: 2
ready robotics Forgelos5 Startup Manual preview
Forgelos5
Brand: ready robotics Pages: 72

Brands by name

Popular brands

Load more brands