manualshive.com logo in svg

GigaDevice Semiconductor GD32A50 Series, User Manual, Page: 394 / 670

Share
Download
GigaDevice Semiconductor GD32A50 Series User Manual Download Page 394

                                                                                                                   

GD32A50x User Manual

 

394 

 

 

101~111: Reserved. 

7 

MCH0COMCEN 

Multi mode channel 0 output compare clear enable. 

When  this  bit  is set,  if  the  ETIFP  signal is  detected  as  high level,  the  MO0CPRE 

signal will be cleared. 

0: Multi mode channel 0 output compare clear disabled. 

1: Multi mode channel 0 output compare clear enabled. 

6:4 

MCH0COMCTL 

[2:0] 

Multi mode channel 0 output compare control   

When multi mode channel 0 is configured in output mode, and the MCH0MSEL[1:0] 

= 2b’00, this bit-field controls the behavior of MO0CPRE  which drives MCH0_O. 

The active level of MO0CPRE is high, while the active level of MCH0_O depends 

on MCH0FP[1:0] bits. 

Note

:  When  multi  mode  channel  0  is  configured  in  output  mode,  and  the 

MCH0MSEL[1:0] = 2b’11, the CH0COMCTL[2:0] bit-field controls the behavior of 

O0CPRE which drives CH0_O and MCH0_O, while the active level of CH0_O and 

MCH0_O depends on CH0P and MCH0P bits. 

000:  Timing  mode.  The  MO0CPRE  signal  keeps  stable,  independent  of  the 

comparison  between  the  register  TIMERx_MCH0CV  and  the  counter 

TIMERx_CNT. 

001: Set the channel output on match. MO0CPRE signal is forced high when the 

counter is equals tothe output compare register TIMERx_MCH0CV. 

010: Clear the channel output on match. MO0CPRE signal is forced low when the 

counter is equals tothe output compare register TIMERx_MCH0CV. 

011: Toggle on match. MO0CPRE toggles when the counter is equals to the output 

compare register TIMERx_MCH0CV. 

100: Force low. MO0CPRE is forced to low level. 

101: Force high. MO0CPRE is forced to high level. 

110: PWM mode 0. When counting up, MO0CPRE is active as long as the counter 

is  smaller  than  TIMERx_MCH0CV,  otherwise  it is  inactive. When  counting  down, 

MO0CPRE  is  inactive  as  long  as  the  counter  is  larger  than  TIMERx_MCH0CV, 

otherwise it is active. 

111: PWM mode 1. When counting up, MO0CPRE is inactive as long as the counter 

is  smaller  than  TIMERx_MCH0CV,  otherwise  it  is  active.  When  counting  down, 

MO0CPRE  is  active  as  long  as  the  counter  is  larger  than  TIMERx_MCH0CV, 

otherwise it is inactive. 

If  configured  in  PWM  mode,  the  MO0CPRE  level  changes  only  when  the  output 

compare mode is adjusted from 

“Timing” mode to “PWM” mode or the comparison 

result changes. 

This bit cannot be modified when PROT[1:0] bit-field in TIMERx_CCHP register is 

11 and CH0NMS bit-field is 00(compare mode). 

3 

MCH0COMSEN 

Multi mode channel 0 output compare shadow enable 

When  this  bit  is  set,  the  shadow  register  of  TIMERx_MCH0CV  register  which 

updates at each update event will be enabled.   

Summary of Contents for GD32A50 Series































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments