manualshive.com logo in svg

GigaDevice Semiconductor GD32A50 Series, User Manual

Introducing the GigaDevice Semiconductor GD32A50 Series user manual, a comprehensive guide brimming with vital information to maximize your product experience. Download this manual for free from manualshive.com and unleash the full potential of your GD32A50 Series device with step-by-step instructions, troubleshooting tips, and much more!

Share
Download
background image

                                                                                                                   

GD32A50x User Manual

 

266 

 

 

0: no effect 

1: Hold the TIMER1 counter for debug when core halted. 

10 

TIMER0_HOLD 

TIMER0 hold bit 

This bit is set and reset by software. 

0: no effect 

1: Hold the TIMER0 counter for debug when core halted. 

9 

WWDGT_HOLD 

WWDGT hold bit 

This bit is set and reset by software. 

0: no effect 

1: Hold the WWDGT counter clock for debug when core halted. 

8 

FWDGT_HOLD 

FWDGT hold bit 

This bit is set and reset by software. 

0: no effect 

1: Hold the FWDGT counter clock for debug when core halted. 

7:3 

Reserved 

Must be kept at reset value. 

2 

STB_HOLD 

Standby mode hold register 

This bit is set and reset by software. 

0: no effect 

1: At the standby mode, the clock of AHB bus and system clock are provided by 

CK_IRC8M (Configured by software), a system reset generated when exit standby 

mode. 

1 

DSLP_HOLD 

Deep-sleep mode hold register 

This bit is set and reset by software. 

0: no effect 

1: At the deep-sleep mode, the clock of AHB bus and system clock are provided by 

CK_IRC8M. 

0 

SLP_HOLD 

Sleep mode hold register 

This bit is set and reset by software. 

0: no effect 

1: At the sleep mode, the clock of AHB is on. 

 

 

Summary of Contents for GD32A50 Series































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32A50 Series

Hal Communications RS2100 Instruction Manual preview
RS2100
Brand: Hal Communications Pages: 25
Qlogic QMC2462S Datasheet preview
QMC2462S
Brand: Qlogic Pages: 2
Wintech TDS510USB Plus Installation Manual preview
TDS510USB Plus
Brand: Wintech Pages: 21
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Brand: Longshine Pages: 27
Tandy 26-3814 Operation Manual preview
26-3814
Brand: Tandy Pages: 24
AC&NC JetStor NAS 724UX User Manual preview
JetStor NAS 724UX
Brand: AC&NC Pages: 117
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12
Omron G3RV-SL500-A Manual preview
G3RV-SL500-A
Brand: Omron Pages: 14
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Brand: Mobatime Pages: 94
Idis DR-8516 Installation Manual preview
DR-8516
Brand: Idis Pages: 28
Aaeon FWS-7811 Manual preview
FWS-7811
Brand: Aaeon Pages: 100
Sennheiser GSP 300 User Manual preview
GSP 300
Brand: Sennheiser Pages: 22
SMC Sierra Monitor FPC-N38 Startup Manual preview
FPC-N38
Brand: SMC Sierra Monitor Pages: 43
ESD C.2044.04 Hardware Manual preview
C.2044.04
Brand: ESD Pages: 30
Datel DataMAX User Manual preview
DataMAX
Brand: Datel Pages: 8

Brands by name

Popular brands

Load more brands