manualshive.com logo in svg

GigaDevice Semiconductor GD32A50 Series, User Manual, Page: 263 / 670

Share
Download
GigaDevice Semiconductor GD32A50 Series User Manual Download Page 263

                                                                                                                   

GD32A50x User Manual

 

263 

 

 

When DSLP_HOLD bit in DBG control register (DBG_CTL) is set and entering the deep-sleep 
mode, the clock of AHB bus and system clock are provided by CK_IRC8M, and the debugger 
can debug in deep-sleep mode.   

When SLP_HOLD bit in DBG control register (DBG_CTL) is set and entering the sleep mode, 
the clock of AHB bus for CPU is not closed, and the debugger can debug in sleep mode. 

13.3.2. 

Debug support for TIMER, I2C, WWDGT and FWDGT 

When the core halted and the corresponding bit in DBG control register (DBG_CTL) is set, 
the following behaved. 

For TIMER, the timer counters stopped and hold for debug. 

For I2C, SMBUS timeout hold for debug. 

For WWDGT or FWDGT, the counter clock stopped for debug. 

For CAN, the receive register is stopped counting for debugging. 

For MFCOM, the counter clock stopped for debug. 

 

 

Summary of Contents for GD32A50 Series































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments