Gigabyte R282-G30 User Manual Download Page 84

Page: 84 / 109

- 84 -

BIOS Setup

5-3-6

Advanced Power Management Configuration

Parameter

Description

Advanced Power Management

Configuration

CPU P State Control

Press [Enter] to configure advanced items.

SpeedStep (Pstates)

– Conventional Intel SpeedStep Technology switches both voltage

and frequency in tandem between high and low levels in response
to processor load.

– Options available: Enable, Disable. Default setting is

Enable

Activate SST-BF

– Enable/Disable SST-BF.

– Options available: Enable, Disable. Default setting is

Disable

Configure SST-BF

(Note)

–

Enable/Disable BIOS to configure SST-BF High Priority Cores

– Options available: Enable, Disable. Default setting is

Enable

Turbo Mode

– When this item is enabled, the processor will automatically ramp

up the clock speed of 1-2 of its processing cores to improve its
performance. When this item is disabled, the processor will not
overclock any of its core.

– Options available: Enable, Disable. Default setting is

Enable

(Note) This item is configurable when

Activate SST-BF

is set to

Enable

Summary of Contents for R282-G30














































































































Search results

Summary of Contents for R282-G30

Reviews:

Gigabyte R282-G30, User Manual, Page: 84 / 109

Search results

Summary of Contents for R282-G30

Reviews: